Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4
4
•
GROUNDING INSTRUCTIONS: In the event of a malfunctions or
breakdown, grounding provides a path of least resistance for electric
current to reduce risk of electric shock. This tool is equipped with an
electric cord having an equipment-grounding conductor and ground-
ing plug. The plug must be plugged into a matching outlet that is
properly installed and grounded in accordance with all local codes
and ordinances. Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The conductor with
insulation having an outer surface that is green with or without yel-
low stripes is the equipment-grounding conductor. If repair or re-
placement of the electric cord or plug is necessary, do not connect
the equipment-grounding conductor to a live terminal. Check with
a qualified electrician or service personnel if the grounding instruc-
tions are not completely understood, or if in doubt as to whether the
tool is properly grounded. Repair or replace damaged or worn cord
immediately
•
THIS TOOL IS INTENDED FOR USE ON A CIRCUIT THAT HAS AN
OUTLET THAT LOOKS LIKE THE ONE ILLUSTRATED IN FIGURE
A. The tool has a grounding plug that looks like the plug illustrated
in figure A. A temporary adapter, which looks like the adapter il-
lustrated in figures B and C, may be used to connect this plug to a
2-pole receptacle as shown in figure B if a properly grounded outlet
is not available. The temporary adapter should be used only until a
properly grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending from the
adaptor must be connected to a permanent ground such as a properly
grounded outlet box.
Fig. A
PERSONAL PROTECTION
Sharpening operations can create hot sparks and metal debris, loud
noises and dust.
•
ALWAYS USE SAFETY GLASSES. Everyday eyeglasses only have
impact resistant lenses, they are NOT safety glasses.
•
USE EAR PROTECTION DURING USE. WORK SHARP
generate in excess of 85 dB(A) noise emissions under certain load
conditions.
•
Use face or dust mask if working operations create dust.
•
WEAR CLOSED, NON FLAMMABLE PROTECTIVE CLOTHING. Do
not wear loose clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Wear protective hair
covering to contain long hair
•
KEEP WORK AREA CLEAN. Cluttered areas and work benches in-
vite accidents.
•
FREQUENTLY CLEAN SHARPENING DEBRIS FROM UNIT AND
WORK AREA.
•
DO NOT USE IN DANGEROUS ENVIRONMENT. Do not use in damp
or wet locations, avoid exposure to rain. Keep work area well lit. Do
not use tools in the presence of flammable liquids or gases.
•
KEEP CHILDREN AWAY. All visitors should be kept safe distance
from work area, do not let persons not involved in the work touch the
tool or power cord.
•
MAKE WORKSHOP KID PROOF with padlocks, master switches, or
by removing starter keys.
•
SECURE WORK. Use clamps or a vise to hold work when practical.
It's safer than using your hand and it frees both hands to operate the
tool.
•
DO NOT FORCE THE TOOL. It will do the job better and safer at the
rate for which it was intended.
•
USE THE RIGHT TOOL. Don't force tool or attachment to do a job
for which it was not designed. Don't force small tools to do the job of
a heavy duty tool. Do not use the tool for purposes not intended.
•
NON-SLIP FOOTWEAR IS RECOMMENDED.
Fig. B
•
NEVER LEAVE TOOL RUNNING UNATTENDED. Ensure tool has
come to a complete stop before leaving work area.
•
MAINTAIN TOOL WITH CARE. Keep WORK SHARP
best and safest performance. Follow instructions for maintenance
and changing accessories. Inspect cords periodically and if damaged
have them repaired by an authorized service facility. Inspect exten-
sion cords periodically and replace if damaged. Keep unit dry, clean
and free from oil and grease.
Fig. C
•
STORE IDLE TOOLS. When not in use, tools should be stored in a
dry, locked-up place out of the reach of children.
•
AVOID UNINTENTIONAL STARTING. Make sure switch is in the
"OFF" position before plugging in.
•
STAY ALERT. Watch what you are doing, use common sense and do
not operate the tool when you are tired or impaired.
•
DON'T OVERREACH. Keep proper footing and balance at all times.
unit can
®
•
NEVER STAND ON TOOL. Serious injury could occur if the tool is
tipped or if the cutting tool is unintentionally contacted.
www.worksharptools.com
www.worksharptools.com
unit clean for
®
Publicité
Table des Matières
