Maintenance - Scheppach LBH2600P Traduction Des Instructions D'origine

9. Maintenance

Injury warning!
Always wear protective gloves when working on
or around the device.
Important!
Always pull out the spark boot plug each time before
carrying out any cleaning.
Never immerse the equipment in water or other liq-
uids in order to clean it.
Store the petrol multi-garden tool in a safe and dry
place out of the reach of children.
Cleaning
• Keep the ventilation slots of the machine clean to
prevent overheating of the engine.
• Regularly clean the machine housing with a soft
cloth, preferably after each use.
• Keep the ventilation slots free from dust and dirt.
• If the dirt does not come off use a soft cloth mois-
tened with soapy water.
• Regularly check the device before starting work.
• Never use water to clean or spray the device. Clean
the motor casing with a damp cloth and never use
detergents or solvents! This may damage the de-
vice's plastic parts. Dry the motor casing carefully
afterwards.
• After shaking out the debris bag, turn it inside out
and thoroughly clean it in order to prevent mould
and unpleasant odors from forming.
• You can use soap and water to clean out a heavily
soiled debris bag.
• Rub a bar of dry soap across the zipper teeth if the
zipper becomes difficult to pull.
• Clean the vacuum/blower tube with a brush upon
evidence of dirt and grime.
• Dirt and grime can make the switch (blower/vac-
uum) more difficult to operate as a result of the
material that swirls up off the ground. When this
occurs, simply flip the switch back and forth a few
times, which should bring it back to the normal
feel.
• Only use OEM parts for maintenance work. Using
parts other than original parts can cause damage
to the machine.
Change and clean the spark plug (Fig. 3)
Check the spark plug air gap at least once a year or
when the engine starts poorly.
The correct gap between ignition flag and ignition
contact is 0.25"/0.63 mm.
• Wait until the engine has cooled down completely.
• Pull the spark plug cap off the spark plug, and
use the supplied spark plug wrench to remove the
spark plug by turning.
• When the electrode is severely worn out or reveals
a strong incrustation, the spark plug must be re-
placed with an equivalent plug.
• A strong incrustation of the spark plug can be
caused by: Amount of oil is too high in the gasoline
mix, poor oil quality, old gasoline mix, or plugged
up air filter.
• Screw the spark plug by hand completely into the
thread. (Avoid jamming it)
• Use the supplied spark plug wrench to tighten the
spark plug.
• When using a torque wrench, the tightening torque
is 12-15 Nm.
• Plug the spark plug socket correctly on the plug.
Clean the air filter(Fig. 4)
Soiled air filters reduce the engine power by sup-
plying too little air to the carburetor. Dust and pollen
plug up the pores of the filter made of foamed plastic.
Regular checks are therefore essential.
• Unclip (A) the air filter cover (B) and remove the
sponge filter element (C).
• To avoid objects falling into the air tank, replace
the air filter cover.
• Wash the filter element in warm soap water, rinse
and allow drying naturally.
Important: Never clean the air filter with petrol or
inflammable solvents.
In order not to shorten the service life of the engine,
a damaged air filter must be replaced at once.
Warning!
Never run the engine without the air filter ele-
ment installed.
FUEL FILTER
Inside the fuel tank there is a filter which prevents
impurities from entering the engine. The filter should
be replaced once a year by your Retailer.
Our machines have been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper machine care and regular cleaning.
Keep all nuts, bolts and screws tight to be sure the
appliance is in safe working condition.
• Replace worn or damaged parts.
• Use only genuine replacement parts and accessories
• Store the appliance only in a dry place.
The user is responsible for all damages caused by
non-compliance with instructions in this manual. This
also applies to non-authorized modifications of the
tool, use of non-authorized spare parts, accessories,
working tools, unrelated and not intended use, sec-
ondary damages due to use of faulty components.
Warning!
Use only original manufacturer's replacement parts,
accessories and attachments. Failure to do so can
cause poor performance, possible injury and may
void your warranty.
GB 27