Page 1 User Manual V2.0 Important Instructions Inspect the packaging for damage and fully charge the product before ﬁrst use. Scan the QR code for the BLUETTI app. Read and understand this manual before use and keep it handy for future reference.
Page 3 Legal Information Notice BLUETTI's products and services are subject to the terms and conditions agreed upon during purchase. Some aspects described in this manual may not be available under your purchase contract. Unless otherwise speciﬁed in the contract, BLUETTI makes no express or implied representations or warranties regarding the contents of this manual.
Page 4 Contents Safety Information What's in the Box Get to Know Your B4810 Install Your B4810 Required Accessories and Tools Installation Requirements Installation Steps Connect Multiple Batteries in Parallel Balance Battery Voltage Connect in Parallel Estimate the Battery SoC Maintenance and Care Speciﬁcations...
Page 5 1. Safety Information 1.1 Important Guidelines BLUETTI is not liable for the following situations or any resulting consequences: • Damage caused by natural disasters, such as earthquakes, ﬁres, ﬂoods, or storms. • Damage due to improper handling or use not in accordance with this manual.
Page 6 If the product gets wet, stop using it immediately. Dry it in a well-ventilated area and avoid contact. Do not reuse after drying; dispose of it according to local regulations or contact BLUETTI support. • In case of ﬁre, use the following in order: water or ﬁne mist, sand, ﬁre blanket, dry powder, and lastly, a CO2 ﬁre extinguisher to put out the ﬁre.
Page 7 2. What's in the Box B4810 Ethernet Cable M8×20 Bolt LiFePO Battery Unit ×2 M5×10 Bolt M8×20 Bolt M8×30 Bolt ×8 ×12 ×2 M8×1.4 Flat Washer M8 Spring Washer M12×12 Headless Bolt ×2 ×2 ×2 M8 Nut Fixed mounting bracket ST8 Wood Screw ×2...
Page 8 Battery Management System (BMS) that protects against overcharging, short circuits, and temperature extremes. With built-in self-heating, the B4810 works reliably even in freezing temperatures as low as -4°F (-20°C), keeping your power consistent. Plus, it allows seamless integration with other devices* for ﬂexible, customized power solutions.
Page 9 4.Install Your B4810 4.1 Required Accessories and Tools Battery Connection Cable* Wrench Screwdriver (9/16") Multimeter Protective Gloves Hex Socket Wrench * Recommended to use a cable larger than 4 AWG or 20 mm 4.2 Installation Requirements WARNING: • Keep the battery away from water, oil, or dirt to prevent leakage, self-discharge, or short circuits.
Page 10 • Install the battery in a clean, dry, and well-ventilated area. If it's in an enclosed space, position it as shown below. Flammable Explosive Rain materials materials High Snow temperature temperature Handle Good Keep dry with care ventilation KEEP DRY FRAGILE VENTILATION Charging: –4°F to 131°F (-20°C to 55°C)
Page 11 4.3 Installation Steps Step 1: POWER OFF the battery. Step 2: Remove the dust covers. Step 3: Install the M8×20 bolts. Step 4: Attach the battery terminals. WARNING - Do not place washers between the terminal bolts and cable lugs to avoid high resistance and overheating.
Page 12 5. Connect Multiple Batteries in Parallel 5.1 Balance Battery Voltage Before connecting batteries, balance their voltage for optimal performance. Step 1: Fully charge each battery using the appropriate charger. Charge controller Battery Fuse Step 2: Use a multimeter to check the voltage of each battery. The difference should be no more than 0.3V.
Page 13 5.2 Connect in Parallel Batteries can be connected in parallel through their terminals or by using a busbar for efﬁcient power distribution. Here's an example with two batteries connected in parallel. LINK OUT LINK OUT LINK IN LINK IN LINK OUT LINK OUT LINK IN LINK IN...
Page 14 Up to 24 batteries can be connected in parallel to expand capacity. For setups with more than 8 batteries, Edock battery communication interface boxes are required. Each box supports up to 8 batteries. TO-BAT LINK-OUT LINK-IN TO-BAT LINK-OUT LINK-IN LINK OUT LINK IN LINK OUT LINK IN...
Page 15 40.0V Note: You can check the remaining battery SoC and upgrade the product by connecting to the BLUETTI app via Bluetooth. 7. Maintenance and Care 1.Do not clean the product with liquids. Use a dry, soft cloth to wipe the surface.
Page 16 8. Speciﬁcations General Model B4810 Battery Capacity 5.12 kWh (51.2V, 100Ah) Net Weight Approx. 101.4 lbs (46 kg) Dimensions (L × W × H) 23.94 × 14.96 × 5.71 in (608 × 380 × 145 mm) General Charging Temperature -4°F to 131°F (-20°C to 55°C), Discharging Temperature -4°F to 131°F (-20°C to 55°C)
Page 17 Modulation mode 2402MHz～2480MHz ≤2dBm GFSK BLE5.0 9. Troubleshooting The B4810 uses red and green lights on the power button to show its status. See the table below for details. Priority Indicator Status Description & Solutions Hardware or unrecoverable failure. Please Flashing Red contact BLUETTI support.
Page 18 10. Battery Performance Charge Discharge Remaining Capacity (%) Charging & dischaging curve at 0.5C, 77°F (25°C) 40°C 55°C 25°C 10°C 0°C -10°C -20°C Remaining Capacity (%) Discharge capacity at 0.5C across different temperatures 1000 2000 3000 4000 5000 6000 7000 8000 Life Cycle Cycle life at 0.5C, 77°F (25°C)
Page 19 Compliance • FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 20 RF exposure statement: The equipment complies with ISED Radiation exposure limits set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
Page 21 Need Help? We're here for you! +1 800-200-2980 (Mon-Sun 9:00-17:00) service@bluettipower.com @ BLUETTI Ofﬁcial @ bluetti_inc @bluetti.inc @bluetti.inc Visit Us BLUETTI Power Inc. 6185 S Valley View Blvd, Ste D, Las Vegas, NV 89118, US https://bluetti.com/...
Page 23 Instructions importantes Inspectez l’emballage pour détecter tout dommage et chargez complètement le produit avant la première utilisation. Scannez le code QR de l’application BLUETTI. Lisez et comprenez ce manuel avant utilisation et gardez-le à portée de main pour référence future.
Page 25 Informations légales Notiﬁcation Les produits et services de BLUETTI sont soumis aux conditions générales convenues lors de l’achat. Certains aspects décrits dans ce manuel peuvent ne pas être disponibles dans le cadre de votre contrat d’achat. Sauf indication contraire dans le contrat, BLUETTI ne fait aucune déclaration ni garantie expresse ou implicite...
Page 26 Table des matières Consignes de sécurité Contenu de la boîte Apprendre à connaître votre B4810 Installer votre B4810 Accessoires et outils requis Conﬁguration requise pour l’installation Étapes d’installation Connecter plusieurs batteries en parallèle Équilibrer la tension de la batterie Connexion en parallèle Estimer l’état de charge de la batterie...
Page 27 1. Consignes de sécurité 1.1 Directives importantes BLUETTI n’est pas responsable des situations suivantes ni des conséquences qui en découlent : • Dommages causés par des catastrophes naturelles, telles que des tremblements de terre, des incendies, des inondations ou des tempêtes.
Page 28 évitez tout contact. Ne le réutilisez pas après séchage ; mettez-le au rebut conformément aux réglementations locales ou contactez le support BLUETTI. • En cas d’incendie, utilisez dans l’ordre : de l’eau ou un brouillard d’eau ﬁn, du sable, une couverture anti-feu, de la poudre sèche et, en dernier recours, un extincteur à...
Page 29 2. Contenu de la boîte B4810 Câble Ethernet Boulon M8 × 20 LiFePO Batterie ×2 Boulon M5 × 10 Boulon M8 × 20 Boulon M8 × 30 ×8 ×12 ×2 Rondelle plate M8 × 1,4 Rondelle élastique M8 Boulon sans tête M12 × 12 ×2...
Page 30 3. Apprendre à connaître votre B4810 Le pack de batteries BLUETTI B4810 est conçu pour les systèmes autres que la propulsion de camping-car, les systèmes autres que la propulsion maritime et les solutions d’énergie domestique. Doté de la technologie lithium-fer-phosphate (LiFePO) ), il offre des performances durables et une sécurité...
Page 31 4. Installer votre B4810 4.1 Accessoires et outils requis Câble de connexion Clé Tournevis à la batterie* (9/16") Multimètre Gants de protection Clé à douille hexagonale * Il est recommandé d’utiliser un câble de calibre supérieur à 4 AWG ou 20 mm 4.2 Conﬁguration requise pour l’installation...
Page 32 • Installez la batterie dans un endroit propre, sec et bien aéré. Si elle se trouve dans un espace clos, positionnez-la comme indiqué ci-dessous. Espace clos Évent Inﬂammable Matières Pluie explosives explosives Température Faible Neige élevée élevée Manipuler Bonne Garder au sec avec précaution ventilation GARDER...
Page 33 4.3 Étapes d’installation Étape 1 : METTRE HORS TENSION la batterie. Étape 2 : Retirer les caches anti-poussière. Étape 3 : Installer les boulons M8×20. Étape 4 : Fixer les bornes de la batterie. AVERTISSEMENT - Ne placez pas de rondelles entre les boulons des bornes et les cosses des câbles pour éviter une résistance élevée et une surchauffe.
Page 34 5. Connecter plusieurs batteries en parallèle 5.1 Équilibrer la tension de la batterie Avant de connecter les batteries, équilibrez leur tension pour obtenir des performances optimales. Étape 1 : Chargez complètement chaque batterie à l’aide du chargeur approprié. Charge contrôleur Fusible de batterie Étape 2 : Utiliser un multimètre pour vériﬁer la tension de chaque batterie.
Page 35 5.2 Connexion en parallèle Il est possible de connecter les batteries en parallèle via leurs bornes ou en utilisant un jeu de barres pour une distribution d’énergie efﬁcace. Voici un exemple avec deux batteries connectées en parallèle. LINK OUT LINK OUT LINK IN LINK IN LINK OUT...
Page 36 Il est possible de connecter jusqu’à 24 batteries en parallèle pour augmenter la capacité. Pour les conﬁgurations avec plus de 8 batteries, des boîtiers d’interface Edock de communication avec les batteries sont nécessaires. Chaque boîtier prend en charge jusqu’à 8 batteries. TO-BAT LINK-OUT LINK-IN...
Page 37 40,0 V Remarque : vous pouvez vériﬁer l’état de charge restant de la batterie et mettre à niveau le produit en vous connectant à l’application BLUETTI via le Bluetooth. 7. Entretien et soins 1. Ne nettoyez pas le produit avec des liquides. Utilisez un chiffon sec et doux pour essuyer la surface.
Page 38 8. Caractéristiques Général Modèle B4810 Capacité de la batterie 5,12 kWh (51,2 V, 100 Ah) Poids net Environ 46 kg Dimensions (L × l × H) 608 × 380 × 145 mm Général Température de charge -20 °C à 55 °C, -20 °C à...
Page 39 2 402 MHz～2 480 MHz ≤ 2 dBm GFSK BLE5.0 9. Dépannage Le B4810 utilise des voyants rouges et verts sur le bouton d’alimentation pour indiquer son état. Pour plus d’informations, reportez-vous au tableau ci-dessous. Priorité État de l’indicateur Description et solutions Panne matérielle ou irrécupérable.
Page 40 10. Performances de la batterie Charge Décharge Capacité restante (%) Courbe de charge et de décharge à 0,5 cycle, 25 °C 40°C 55°C 25°C 10°C 0°C -10°C -20°C Capacité restante (%) Capacité de décharge à 0,5 cycle à différentes températures 1 000 2 000 3 000 4 000 5 000 6 000 7 000 8 000 Cycle de vie Durée de vie en nombre de cycles à...
Page 41 Compliance • IC Caution L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) L' appareil ne doit pas produire de brouillage; (2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en compromettre le fonctionnement.
Page 43 Manual del usuario V2.0 Instrucciones importantes Inspeccione el embalaje para detectar daños y cargue completamente el producto antes del primer uso. Escanee el código QR de la aplicación BLUETTI. Lea este manual antes de usar la unidad y consérvelo para futuras consultas.
Page 45 Información legal Aviso Los productos y servicios de BLUETTI están sujetos a los términos y condiciones acordados durante la compra. Es posible que algunos aspectos descritos en este manual no estén disponibles según su contrato de compra. A menos que se especiﬁque lo contrario en el contrato, BLUETTI no ofrece garantías expresas ni...
Page 46 Contenido Información de seguridad Contenido de la caja Conozca su B4810 Instale su B4810 Accesorios y herramientas necesarios Requisitos de instalación Pasos de instalación Conectar varias baterías en paralelo Equilibrar el voltaje de la batería Conectar en paralelo Estimar el SoC de la batería Mantenimiento y conservación...
Page 47 Daños resultantes de negligencia, mal uso o daño intencionado del cliente. • Daños causados por desmontaje, modiﬁcación o reparaciones sin autorización. • Daños causados por el uso de dispositivos que no sean BLUETTI para alimentar este producto. • Lesiones, incendios o mal funcionamiento del equipo resultantes del uso de este producto en aplicaciones críticas (como energía nuclear, aviación o medicina), en las...
Page 48 No lo reutilice después del secado; deséchelo de acuerdo con la normativa local o póngase en contacto con el servicio de atención al cliente de BLUETTI. • En caso de incendio, utilice lo siguiente en orden para apagar el fuego: agua o aerosol ﬁno, arena, manta ignífuga, polvo seco y, por último, un extintor de CO2.
Page 49 2. Contenido de la caja B4810 Cable Ethernet Perno M8×20 LiFePO Unidad de batería ×2 Perno M5×10 Perno M8×20 Perno M8×30 ×8 ×12 ×2 Arandela plana M8×1,4 Arandela elástica M8 Perno sin cabeza M12×12 ×2 ×2 ×2 Tuerca M8 Soporte de montaje ﬁjo Tornillo para madera ST8 ×2...
Page 50 3. Conozca su B4810 La batería BLUETTI B4810 está diseñada para sistemas no motrices de vehículos recreativos, sistemas marinos sin propulsión y soluciones de energía para el hogar. Alimentada con tecnología de litio-ferrofosfato (LiFePO ), ofrece un rendimiento duradero y una seguridad de primer nivel, respaldada por un sistema de gestión de baterías (BMS) inteligente que protege contra sobrecargas, cortocircuitos y...
Page 51 4. Instale su B4810 4.1 Accesorios y herramientas necesarios Cable de conexión Llave Destornillador de la batería* (9/16") Multímetro Guantes de protección Llave de tubo hexagonal * Se recomienda utilizar un cable de más de 4 AWG o 20 mm 4.2 Requisitos de instalación...
Page 52 • Instale la batería en una zona limpia, seca y bien ventilada. Si está en un espacio cerrado, colóquela como se muestra a continuación. Espacio cerrado Aire Respiradero Materiales Materiales Lluvia inﬂamables explosivos Alta Baja Nieve temperatura temperatura Manejar Buena Mantener seco con cuidado ventilación...
Page 53 4.3 Pasos de la instalación Paso 1: APAGUE la batería. Paso 2: retire las tapas antipolvo. Paso 3: instale los pernos M8×20. Paso 4: conecte los terminales de la batería. ADVERTENCIA - No coloque arandelas entre los pernos de los terminales y los terminales de cable para evitar la alta resistencia y el sobrecalentamiento.
Page 54 5. Conectar varias baterías en paralelo 5.1 Equilibrar el voltaje de la batería Antes de conectar baterías, equilibre su voltaje para obtener un rendimiento óptimo. Paso 1: cargue completamente cada batería utilizando el cargador adecuado. Carga Controlador Fusible de batería Paso 2: utilice un multímetro para comprobar el voltaje de cada batería.
Page 55 5.2 Conectar en paralelo Las baterías se pueden conectar en paralelo mediante sus terminales o utilizando una barra colectora para una distribución eﬁciente de la alimentación. A continuación se muestra un ejemplo con dos baterías conectadas en paralelo. LINK OUT LINK OUT LINK IN LINK IN...
Page 56 Se pueden conectar hasta 24 baterías en paralelo para ampliar la capacidad. Para conﬁguraciones con más de 8 baterías, se requieren cajas de interfaz de comunicación de batería eDock. Cada caja admite hasta 8 baterías. TO-BAT LINK-OUT LINK-IN TO-BAT LINK-OUT LINK-IN LINK OUT LINK IN...
Page 57 40,0 V Nota: Puede consultar el SoC restante de la batería y actualizar el producto conectándose a la aplicación BLUETTI mediante Bluetooth. 7. Mantenimiento y conservación 1. No limpie el producto con líquidos. Utilice un paño seco y suave para limpiar la superﬁcie.
Page 58 8. Especiﬁcaciones General Modelo B4810 Capacidad de la batería 5,12 kWh (51,2 V, 100 Ah) Peso neto Aprox. 101,4 lb (46 kg) Dimensiones (largo × ancho × alto) 23,94 × 14,96 × 5,71 in (608 × 380 × 145 mm)
Page 59 2402 MHz～2480 MHz ≤2 dBm GFSK BLE5.0 9. Solución de problemas B4810 utiliza luces rojas y verdes en el botón de encendido para mostrar su estado. Consulte la tabla siguiente si desea más información. Prioridad Estado del indicador Descripción y soluciones Fallo de hardware o no solucionable.
Page 60 10. Rendimiento de la batería Carga Descarga Capacidad restante (%) Curva de carga y descarga a 0,5C, 77 °F (25 °C) 40°C 55°C 25°C 10°C 0°C -10°C -20°C Capacidad restante (%) Capacidad de descarga a 0,5C a diferentes temperaturas 1000 2000 3000 4000 5000 6000 7000 8000 Ciclo de vida Ciclos de vida a 0,5C, 77 °F (25 °C) JUST POWER ON...
Page 63 ¿Necesita ayuda? Estamos aquí para ayudarle +1 800-200-2980 (de lunes a domingo de 9:00 a 17:00) service@bluettipower.com @ BLUETTI Ofﬁcial @ bluetti_inc @bluetti.inc @bluetti.inc Visítenos BLUETTI Power Inc. 6185 S Valley View Blvd, Ste D, Las Vegas, NV 89118, US...
Page 64 Cer t iﬁc a te Inspector: Q C : P/N: 17.0303.0922-01A1...
Page 65 Power Hub User Manual V1.0 Important instructions • Read and understand this manual before use and keep it handy for future reference.
Page 66 Tips 1. Before ﬁrst use, make sure the connected batteries are in good condition and functioning properly. 2. Only connect devices that meet the voltage requirements for each port. 3. Do not connect the unit's AC output to the grid. 4.
Page 67 Shenzhen PowerOak Newener Co., Ltd. Notice BLUETTI's products and services are subject to the terms and conditions agreed upon during purchase. Some aspects described in this manual may not be available under your purchase contract. Unless otherwise speciﬁed in the contract, BLUETTI makes no express or implied representations or warranties regarding the contents of this manual.
Page 68 Contents About the Manual Safety Instructions------------------------------------------------------------------------------------ 1.1 General Instructions ------------------------------------------------------------------------------ 1.2 Installation Safety---------------------------------------------------------------------------------------------- 1.3 Battery Safety -------------------------------------------------------------------------------------------------- 1.4 Electrical Safety ----------------------------------------------------------------------------------- 1.5 Handling Requirements------------------------------------------------------------------------- 2. What's in the Box ------------------------------------------------------------------------------------------------- 3. Get to Know Your RV5 ------------------------------------------------------------------------------- 3.1 System Overview --------------------------------------------------------------------------------- 3.2 RV5 Introduction---------------------------------------------------------------------------------- 4.
Page 69 5. Use Your RV5 ------------------------------------------------------------------------------------------------------- 5.1 Power On/Off -------------------------------------------------------------------------------------------------- 5.2 Initial Setup ---------------------------------------------------------------------------------------------------- 5.3 Conﬁgure Your RV5 ------------------------------------------------------------------------------ 5.4 Button Control------------------------------------------------------------------------------------ 6. Maintenance and Care ------------------------------------------------------------------------------ 7. Speciﬁcations------------------------------------------------------------------------------------------------------ 8. Troubleshooting -------------------------------------------------------------------------------------------------- Appendix 1------------------------------------------------------------------------------------------------------------ --- Appendix 2 -------------------------------------------------------------------------------------------------------------- Appendix 3 -------------------------------------------------------------------------------------------------------------- Compliance ------------------------------------------------------------------------------------------------------------- 1.
Page 70 About the Manual Purpose This user manual describes the installation, electrical connection, commissioning, maintenance and troubleshooting of RV5. Please read and understand all instructions in this manual before use. Symbol Conventions This manual uses the following symbols to highlight important information: Danger It indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Page 71 Our company shall not be liable for damages resulting from non-compli ance with these safety requirements or standards. For issues or operations not covered in this manual, please contact BLUETTI support, otherwise we are not responsible for any damage or injury caused by unauthorized operations.
Page 72 mudslides. • Transport-related damages during customer handling. • Equipment damage due to improper storage conditions as outlined in the manual. • Hardware damage or data loss resulting from customer negligence, improper use, or intentional damage. • System damage caused by third parties or customers, including improper handling or installation not in line with the manual's instructions.
Page 73 12. Do not move the unit during operation, as vibrations and shocks from movement may cause damage. 13. In case of malfunction, immediately power the unit off and contact BLUETTI support or your local BLUETTI dealer if the manual does not adequately explain the issue.
Page 74 1.2 Installation Safety Danger Follow these guidelines for proper use. 1. Avoid working with live electrical components. 2. Before installation, double check the unit for any signs of damage or defects to minimize potential risks. 3. Make sure the unit and all associated switches are turned off (not in sleep mode) to prevent electric shock.
Page 75 When installing this device, the battery is to be veriﬁed as in compliance with the applicable battery standard. 5. CAUTION – It's recommended to use battery packs provided by BLUETTI. Unveriﬁed, damaged, or modiﬁed batteries may pose ﬁre, explosion, or injury risks. If using a third-party battery, follow its user manual for proper use and maintenance.
Page 76 1. Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid battery. 2. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
Page 77 1. Before operating the unit, always conﬁrm that it is properly grounded to reduce the risk of electric shock. 2. Take care not to damage the grounding conductor. 3. Connections to unit should comply with all local codes and ordinances. 4.
Page 78 Power Hub User Manual & Warranty Card Drilling Template M8 Wood Screw ×8 Anchor x8 The following accessories are not included. You can purchase optional accessories at https://www.bluettipower.com/ B4810 Epanel Epad LiFePO4 Battery Unit Smart Distribution Panel Central Control Screen Edock...
Page 79 The RV5 System is a complete energy solution designed for RVs, boats, and off-grid power setups. At its core, the RV5 5-in-1 power hub integrates seamlessly with the B4810 battery, Epad control pad, Epanel distribution panel, and PV100 FX solar panel, providing efﬁcient manage- ment and monitoring of both DC and AC power.
Page 80 3.1.2 RV System Wiring Epad Epad AC Inputs AC Inputs AC Appliance AC Appliance Chassis Chassis Starter Starter Chassis Chassis battery battery PV100 FX PV100 FX Epanel Epanel B4810 B4810 DC Appliance DC Appliance RV system wiring JUST POWER ON...
Page 81 3.1.3 Off-grid System Wiring Epad AC Inputs AC Appliance PV100 FX PV100 FX Epanel B4810 DC Appliance Off-grid system wiring JUST POWER ON...
Page 82 3.2 RV5 Power Hub 3.2.1 Dimensions JUST POWER ON...
Page 83 3.2.2 Overview ① ⑨ DC Power Button PV1 Input ② ⑩ Power Button PV2 Input ③ ⑪ AC Power Button Battery Temperature Sampling Port ④ ⑫ LCD Display Battery Communication Port ⑤ ⑬ Grounding Terminal* Battery Terminal ⑥ ⑭ EMS Communication Port AC Input (N/L1/L2/G) ⑦...
Page 84 3.2.3 LCD Display ① ⑪ DC Output ② ⑫ PV Input AC Output ③ ⑬ Bluetooth Connection Remaining Time ④ ⑭ WiFi Connection Charge / Discharge Status ⑤ ⑮ State of Charge (SoC) High Temperature ⑯ Capacity Progress； Overload ⑥ ⑰...
Page 85 4. Set up Your RV5 Danger • Do not install the unit below pipes, windows, or in areas prone to water leaks and accumulation. • Disconnect all electrical connections from the unit before installation. Warning • Do not block ventilation openings or heat dissipation pathways. •...
Page 86 4.2 Mount the RV5 4.2.1 Space Requirements Make sure there's at least 8in (20cm) of space around the unit for cables and airﬂow as shown below. Hot air Cool air ≥200mm/7.87in ≥200mm/7.87in Space requirements If the RV5 operates in a high-temperature environment without proper ventilation, its charging and discharging power will decrease.
Page 87 4.2.2 Mounting Instructions Danger • Before drilling, check for nearby water pipes or electrical cables to avoid any hazards. • The included M8 screws and anchors are for wooden and cement walls. Use suitable screws for other surfaces to ensure a secure installation. RV5 can be installed in two ways: wall-mounted or ﬂoor-mounted, using different screw holes shown below.
Page 88 A. Wall-Mounted Installation Step 1: Select a suitable location. Tape the drilling template to the wall and mark the keyholes. Step 2: Use a #2 screwdriver to fasten the M8 screws into the keyhole slots. Step 3: Hang the RV5 on the screws. Step 4: Ensure all screws are ﬁrmly tightened.
Page 89 B. Floor-Mounted Installation Step 1: Select a suitable location. Tape the drilling template to the wall and mark the round holes. Step 2: For cement walls, drill holes at the marked points and insert the anchors. Step 3: Secure the unit by driving M8 screws into the anchor. For other wall materials, drive the appropriate screws into the wall.
Page 90 4.2.3 Install the Waterproof Cover In rainy areas, you can install the optional waterproof cover above the fan vent to prevent ceiling drips. Waterproof cover installation JUST POWER ON...
Page 91 4.3 Wire and Fuse Speciﬁcations For best performance and safety, use the shortest and thickest cables possible. Undersized cables can overheat and cause a ﬁre risk. If you're unsure about the right cable size, contact BLUETTI support or consult a professional. Recommended Connection...
Page 92 4.4 Wiring Overview Step 1 Make sure the unit is intact and securely mounted. Step 2 Remove the two external screws and take off the ﬁrst cover. Keep the screws and set the cover aside. Step 3 Remove the second panel (no screws).
Page 93 Connect the commu nication cables. Step8 Secure the ﬁrst cover with all screws. Step9 Connect the ground ing cable. Step10 Power on the unit and complete the initial setup in the BLUETTI Press and hold for 2 seconds. app. JUST POWER ON...
Page 94 4.5 AC Input Wiring The RV5 supports both single-phase 120V input and 208V/240V input (EV charging mode). Below is the power ﬂow for each mode: Bypass Mode (120V Input) EV Charging Mode (208V/240V Input) JUST POWER ON...
Page 95 4.5.1 Shore Power Connect the AC input cable from the RV5 to a 120V shore power inlet. Note: A 3-pin RV adapter is required. Single-phase 120VAC shore power charging 4.5.2 Generator Connect the RV5 to a gasoline, propane, or diesel generator using the AC charging cable. The charging stops automatically when the battery is fully charged.
Page 96 If using the Epad, connect its DO port to the generator's start signal port for black start. For more details, refer to the Epad User Manual. Attention Make sure the generator delivers a pure sine wave output with matching voltage and frequency. Ensure the generator's output power exceeds the RV5's charging requirements.
Page 97 4.6 AC Output Wiring The RV5 supports AC output of up to 5,000W and 42A for single-phase 120V AC appliances. In bypass mode, it can handle up to 6,000W and 50A. For optimal performance, it's recommended to use the Epanel to manage the AC output current.
Page 98 Battery Model Conﬁguration Current Limit Notes For setups with more than 1S1P 1C (A) 8 batteries, Edocks are B4810 required. See Appendix 1 1SnP (n = 24P Max. ) 150A for wiring details. 4S1P 1C (A) See Appendix 2 for wiring B1210/B1228 details.
Page 99 4.7.2 B4810 Battery To achieve full power output, it is recommended to pair the RV5 with two B4810 battery packs, providing a total capacity of 10kWh. When used with a single B4810, the total load power is approximately 4320W.
Page 100 Step 1: Prepare two power cables (bare ends on both sides—red for positive, black for negative ) and the pre-assembled B4810 battery packs based your load requirements. Step 2: Connect the black power cable from the RV5's BAT- port to the B4810's main negative terminal.
Page 101 The maximum charging current for lead-acid batteries is set at 0.2C, with the constant charging voltage adjusted for temperature. Non-communication lithium batteries have a maximum charging current of 0.5C. Since lead-acid batteries cannot release their full capacity under high-rate discharge conditions, and it is easy to accelerate the corrosion of the lead-acid battery plates and capacity decay, please try to avoid frequent or continuous high-rate discharge.
Page 102 Step 6: Ensure that all connections are secure. Warning When using lead-acid batteries or non-BLUETTI battery packs: 1. Ensure correct wiring polarity. Damage from reversed polarity is not covered under warranty.
Page 103 The RV5 comes with two DC input ports, PV1 and PV2. Each supports up to 50A and 1,800W of solar charging power, totaling 3,600W. The charging time may vary based on weather conditions, sunlight intensity, panel orientation, and other variables. Note: The function of PV2 port can be set through the APP RV5+PV100 FX wiring（6 pcs）...
Page 104 If you're unsure about the required fuse rating, consider using the optional cable kit provided by BLUETTI or contacting BLUETTI support for assistance. Connect the RV5 to your vehicle's starter battery via the PV2 ports. The required connec- tion cable and fuse are included in the optional cable kit.
Page 105 4.9 DC Output Wiring The RV5 supports both 12V and 24V DC output. Select the appropriate voltage based on your battery system requirements and conﬁgure the settings before ﬁrst use. For setup details, refer to the App User Manual. Supported Output: •...
Page 106 4.10 Grounding For temporary AC input connections, such as in an RV or marine setup, the unit must be grounded to the vehicle chassis or the boat's hull or grounding plate. Follow the instruc- tions below for proper installation: Step 1: Prepare a grounding cable (recommended to use 10mm2 yellow-green outdoor cable), RNB14-6S OT terminal, and M6 screws (pre-installed on the unit).
Page 107 4.11 CAN Communication Wiring & Conﬁguration To ensure seamless communication among your BLUETTI devices, connect and conﬁgure them as shown below. Incorrect setup may lead to communication issues. Note: Do not plug the battery communication cable into the Epad or Epanel ports.
Page 108 RV5 + B4810 + Epanel + Epad RV5 + B4810 + Epad RV5 + B4810 + Epanel JUST POWER ON...
Page 109 Press and hold the power button for 2 seconds while it's off or in sleep mode. The lit button indicates that the RV5 is on. For initial use, complete the setup in the app. If you're using BLUETTI B4810, B1210, B1228, or B300 series batteries, you can also power on the unit via the app.
Page 110 The RV5 features a sleep mode to extend battery life. In this mode, it charges the battery with up to 100W solar power while keeping the display off. When connected to a network, the RV5 also supports remote wake-up. Enter the mode: With the unit on, press and hold the power button for about 2 seconds until the display turns off.
Page 111 By default, the unit charges in Standard mode. Charging Power Charging Time Mode (for Single (for two AC + PV B4810 Units) B4810 Units) Standard 1,440W Max. 2,000W Max . 2,000W Max. 2.5 ho urs 4.5 hours 80% charge 80% charge Turbo in 50 mins;...
Page 112 5.3.2 Adjust Grid Input Current The default maximum grid input current is 12A. Use the app to increase it up to 50A. For safety, set the maximum input current to 80% of your outlet's rated capacity. Alternatively, consult an electrician to conﬁrm that the outlet can handle the current. 5.3.3 Grid Self-Adaption Mode When connecting with a generator or unstable grid power, or if consumption power exceeds charging power, enable this mode in the app.
Page 113 6. Maintenance and Care Always power off the system before performing maintenance tasks such as cleaning, checking connections, and verifying grounding. The RV5 requires regular maintenance, including: • Inspect and clean the fan, fan guard, and heat sink if dust or blockages are present. •...
Page 114 -4°F to 131°F (-20°C to 55°C) Working altitude ≤2000m Operating Humidity 95% Max. Certiﬁcation UL458 [1]Compatible with B4810, B1210, B300 series, and other lithium and lead-acid batteries. [2]Power limits may vary based on ambient temperature and the connected battery capacity. JUST POWER ON...
Page 115 8. Troubleshooting On the Error Code page, the and error code appears simultaneously on the display. See the table below for guidance. Error Code Description Solutions • Check device power usage. E001 Inverter overload • Reduce load if too high. •...
Page 116 • Ensure the Ethernet cable is properly Battery System connected to the battery pack. E070 communication • If using a non-communication battery, failure make sure it's set accordingly. • Please handle according to the attached BMS system failure E075 battery pack fault code. •...
Page 117 FAQs (Frequently Asked Questions) Q1: Can I use third-party solar panels with this unit? A: Yes, you can use third-party solar panels with open circuit voltage of 12V-50V. Avoid mixing different types of solar panels. Q2: Does it support charging and discharging at the same time? A: Yes, RV5 supports pass-through charging as long as EV charging is not activated.
Page 118 Choose the appropriate busbar pair size based on the number of connected battery packs, ensuring a minimum current capacity of 150A. For more than two B4810 units, we recommend using a busbar pair to keep cable lengths consistent for each connection to the RV5.
Page 119 Appendix 2 B1210 + Edock connection JUST POWER ON JUST POWER ON...
Page 120 Appendix 3 B300K connection Note: The RV5 supports connecting up to four B300 units. JUST POWER ON JUST POWER ON...
Page 121 Compliance • FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 122 • IC Caution This device contains licence-exempt transmitter(s) / receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Page 123 +49 8006273016 Monday to Friday 9:00 - 17:00 Customer Service(UK) service@bluettipower.com +44 8000472906 Monday to Friday 9:00 - 17:00 @ BLUETTI Ofﬁcial @ bluetti_inc @bluetti.inc @bluetti.inc Visit Us SHENZHEN POWEROAK NEWENER CO., LTD. 19F, Block A, Kaidaer Bldg., No. 168 Tong Sha Rd, Shenzhen, China BLUETTI Power Inc.
Page 124 JUST POWER ON...
Page 125 À propos le Manuel Ce manuel utilisateur décrit le installation, électrique connexion, mise en service, entretien et dépannage de RV5. S'il te plaît lire et comprendre tous instructions dans ce manuel avant utiliser. Symbole Conventions Cemanuel utiliser s le suivant symboles à souligner important information : Danger Il indique un dangereux situation lequel, si pas évité, volonté...
Page 126 Pour problèmes ou opérations pas couvert dans ce manuel, s'il te plaît contact BLUETTI soutien, autre Nous ne sommes pas responsables des dommages ou blessures causés par des opérations non autorisées.
Page 127 8. Éviter non autorisé démontage, équipement modiﬁcations, ou logiciel code modiﬁcations. 9. Notre entreprise devoir aussi pas être responsable pour le suivant situations ou leur conséquences: • Dommage causé par forcer majeure événements tel comme tremblements de terre, incendies, tempêtes, inondations, ou coulées de boue. •...
Page 128 13. Dans cas de mauvais fonctionnement, immédiatement pouvoir le unité désactivé et contact BLUETTI soutien ou ton locale BLUETTI revendeur si le manuel fait pas adéquatement expliquer le problème. 14. Monter le unité en toute sécurité sur un métal support, mur, ou écurie plate-forme à prévenir il depuis chute.
Page 129 Note Se conformer avec en vigueur lois et règlements. • Quand manutention, installation, câblage, ou maintenir ce produit, se conformer avec le pays ou région légal règlements et normes. • Utiliser matériels et outils que rencontrer en vigueur légal exigences et normes. •...
Page 130 n'importe lequel autre aspects sans autorisation. 1.2.2 Forage Exigences Quand forage trous dans le mur ou sur le sol, suivre ces sécurité mesures: 1. Porter lunettes de protection et protecteur gants à tous fois. 2. Bouclier le unité à prévenir débris depuis chute dans il, et retirer tous débris après forage. 3.
Page 131 être vériﬁé comme dans conformité avec le en vigueur batterie standard. 5. ATTENTION – Il est recommandé d'utiliser les batteries fournies par BLUETTI. Non vériﬁé, endommagé, ou modiﬁé piles peut pose feu, explosion, ou blessure risques. Si en utilisant un tierce personne batterie, suivre c'est utilisateur manuel pour approprié...
Page 132 11. Faire le ménage batterie terminaux. Être prudent à garder corrosion depuis à venir dans contact avec yeux. 12. Étude tous batterie du fabricant spéciﬁque précautions tel comme suppression ou pas suppression cellule casquettes alors que charge et recommandé tarifs de charge. 13.
Page 133 différent types de câbles à moins 1,18 pouces (30 mm) à part et éviter torsion ou passage eux. 3. Tous câble doit être en toute sécurité connecté, bien isolé, et de approprié caractéristiques. 4. Prendre nécessaire mesures à protéger câbles quand passage à travers tuyaux ou trous. 5.
Page 134 Conformité • Déclaration de la FCC (1) L’appareil ne doit pas produire de brouillage nuisible. (2) L’appareil doit accepter tout brouillage subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Cet équipement a été testé et jugé conforme aux limites d’un appareil numérique de fournir une protection raisonnable contre les brouillages nuisibles dans une installation résidentielle.
Page 135 • Mise en garde d’IC L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Page 136 Cer t iﬁ ca te Inspector: Q C : P/N:17.0303.0898-00...

Bluetti B4810 Manuel D'instructions

Liens rapides

Manuels Connexes pour Bluetti B4810

Sommaire des Matières pour Bluetti B4810