Cequent Performance Products 65061 Instructions D'installation

Receiver Shown In Pro
Equipment Required:
Fastener Kit: 65061F
Wrenches: 3/4", 7/8", 15/16"
15mm, if removing air dam
Drill Bits: None
Other Tools: Tape, Cutting
tool forhard plastic fascia.
ooo
0000000
Qty. (2) Hex Bolt, 1/2"-13 x 6" Gr5
Qty- (2) Flat Washer,
Qtyc (4) Conical Washer,
Qty. (2) Hex Nut, 1/2"
Qty. (2) Tube, Spacer x 4-1/4"
1. It is necessary to trim a section out of the fascia. See Picture above. Note: For 2011 and newer trucks the air dam must be removed. Use 15mm wrench
to remove (2) nuts holding air dam_
2. Insert 1/2" x 6" long bolts through conical washers and install through 1" diameter holes on the inside of truck frame rails.
3- Slide the spacer tubes onto the 1/2" x 6" bolts by inserting them from the outside of truck frame rails_
4. Secure 1/2" flat washers on outside of truck frame rails using tape as shown in the picture above-
Gently pull bolts back so that the end ofthe bolts are even with the washers, this is so the hitch can be raised into position.
Position hitch and raise into position being carefrl not to knock off taped washers on frame- hl.stall fisteners as shown above.
5. Use 5/8" bolt leaders to pull 5/8" carriage bolts into frame slots and through hitch. Square shoulders ofbolts
of frame slots- Use access slots on inside of truck frame as shown above to pull 5/8" carriage bolts through- Note: It may be necessary to file slots
some truck frames to allow bolts to pass
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft
fr*ltb' unking sure all å starrs a nd b an a re
Note: clrck hdch
A hitch or ball which damaged should
with a torch
This with
0 2012 Cequent Performance Products, Inc.
Front Mounted Receiver
Ford F-150,
All including XL, XLT, STX, FX2, FX4, EcoBoost, Lariat,
King Ranch,
Lincoln Mark LT —Mexico only
*Raptor requires front skid-shield
* *Harley-Davidsou
er Position
This is a magnified
view
008
Fasteners typical both sides of vehicle
1/2"
1/2"
CONSULT VEHICLE OWNER
more easily. Or you can pull bolts through end of frame above recovery eyes on 4WD models _
removed
and for coarcting devicesandtowingsysteuzoftlrstateofNewYork,
Installation
2WD & 4WD Models
Raptor &
modification.
versions may push up on plastic air- dam.
of a Bolt Leader
carriage bolts from
O Qty. (2)
Qty. (2)
Qty. (2)
Qty. (2)
Qty. (2)
BEFORE TRAIMLNG OR CUTTING
(102 N-M). Tighten all 5/8" GR5 fasteners with torque wrench to 150 Lb.-Ft
Sheet I of 3
Instructions
All 4 WD
CARGO CAPACITY
500 LB. or Truck
Gross Axle Weight Rating, (GAWR).
9,0001b. MAXIMUM
Tape 1/2" flat washer in to
depression around hole on outside of
frame both
Optional to pull
end of frame on
4WD trucks.
2011 & Up
Trim fiscia 1-3/8" from bottom by 3-12" wide
for 1"
Verify dimensions before trimming fascia.
Carriage Bolt, 5/8"-11 X 2" Gr5
Conical Washer, 5/8"
Hex Nut, 5/8"
1.50" x 2.00" Block
Pull Wire
FASCW
must be pulled out to engage with sides
Do IDt c ut a ccess
SAE J684.
65061 N 9-5-12
Part Numbers:
65061
trucks come standard
with recovery eyes,
model trucks do not_
- Do not exceed
Front
WINCH LINE PULL
sides of truck.
from bottom by 3-1/2" wide for
2WD trucks.
on
(203 N-M).
orattac=tholes
Rev_ A