Cequent Performance Products 24861 Instructions D'installation

Fascia
Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24861F
Wrenches: 3/4, 7/8, 10mm
Drill Bits: None
1
2
Qty. (2) 1/2"-13 x 1-1/4" Hex Bolt Gr.5 , (Torque to 50 Ft. Lb.)
1
2 Qty. (4) 1/2" Conical Toothed Washer
3
Qty. (2) 1/2"-13 Handle Nut
1. Lower vehicle exhaust by removing tailpipe tangs out of rubber exhaust hanger at rear of vehicle.
2. On the Passenger's side remove the (4) bolts that attach the exhaust heat shield to the vehicle. (Do not Discard).
3. On the Driver's side, remove the plastic rivet and nut that hold the plastic shroud to the frame rail. (Do not Discard).
4. Raise hitch into position with frame bracket flanges between the frame rail and plastic shroud on the Driver's side and between
the frame rail and exhaust heat shield on the Passenger's side. Make sure that tailpipe tangs are above hitch bar while raising
hitch in to place. On some vehicles it may be necessary to remove chrome decorative ring off of end of tailpipe to allow muffler
to slide sideways toward middle of vehicle to allow better wrench access.
5. Insert 1/2"-13 handle nuts through the large holes in vehicle frame rails and install fasteners as shown above.
6. Insert the 1/2-13 x 2-1/4"bolt and toothed washer through the slot in the hitch then through the vehicle tow hook and back
through the hitch. Install toothed washer on other side then locknut. (see above).
7. Pull hitch rearward as far as possible to allow muffler clearance with hitch bar on passenger's side. Tighten all fasteners to the
required torque specifications shown below.
8. Reinstall exhaust heat shield over hitch. Heat shield may require trimming. Reattach exhaust to hanger & replace rivet and nut
holding plastic shroud on driver's side. Reattach chrome decorative ring to tailpipe if removed.
Tighten 1/2"-13 x 1-1/4" Hex Bolts with torque wrench to 50 Lb.-Ft. (68 N*M) Tighten 1/2"-13 x 2-1/4" Hex Bolt to 75Lb.-Ft. (102 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
© 2010, 2011, 2012 Cequent Performance Products - Printed in Mexico
Installation Instructions
Acura CSX
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
Vehicle
frame rail
Heat shield
3
1
2
Tow hook
4
2
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
3
Exhaust
2
5
Qty. (1) 1/2-13 x 2-1/4" Hex Bolt Gr.5, (Torque to 75 Ft. Lb.)
4
5 Qty. (1) 1/2-13 Lock Nut
Another Fine Cequent Performance Products Hitch
Sheet 1 of 3 24861N
Part Numbers:
24861
60277
77247
24888
U-Haul
Note!
Torque is different for
bolts in to frame than
bolt through tow hook.
See torque spec below.
2-2-12 Rev. C