Using The Appliance; Operation And Use - WMF Stelio Mode D'emploi

WMF milk froth DISC
The WMF milk froth DISC (3) can be removed from the appliance for easy cleaning. To do this, gently
push down the WMF milk froth DISC (3) and slide it to one side.
To assemble the appliance, proceed as follows:
Simply slide the WMF milk froth DISC (3) sideways into the appliance, an internal magnet holds the
DISC firmly in place.

Using the appliance

Before using for the first time, ensure the appliance is thoroughly cleaned, as detailed in the "cleaning
and care" section.
Any surplus cable can be wound into the bottom of the base unit (6). Connect the mains plug to an
earthed socket.

Operation and use

1. Add the required amount of milk to the jug (4) and close it with the lid (1).
2. Place the jug (4) on the base (6).
Warning:
Always place the lid (1) securely on the jug before switching it on.
Never remove the lid (1) while the appliance is running.
Note:
Preparation can be stopped at any time by lifting the jug (4) off the base (6).
Allow the appliance to cool down before reuse.
The quality and volume of the milk froth depends on the milk used (e.g. the fat and protein content,
temperature, etc.).
12
Hot milk froth
Select this programme for hot, creamy, fine milk froth. This is particularly suitable for cappuccino or
latte.
▪ Add 100 to 150 ml of milk to the jug (4).
The filling marks are in the jug (4):
100 ml MIN
150 ml MAX
Do not add more than that, otherwise the milk froth will overflow and soil the appliance.
▪ Place the lid (1) on the jug (4) and apply slight pressure to ensure a good seal.
▪ Press the Start/Stop button (5) until the symbol lights up red. After around five seconds the
frothing starts automatically.
▪ After the programme ends, the appliance switches off automatically and the indicator light turns
off. Remove the lid (1) and skim off the milk froth separately, or pour it out with the remaining
milk.
Warning: Do not use any sharp metallic objects for skimming off the froth, as this can damage the
coating.
Cold milk froth
Select this programme for cold, creamy, milk froth. This is particularly suitable for frappé drinks,
cocktails, iced coffee and desserts.
▪ Add 100 to 150 ml of milk to the jug (4).
The filling marks are in the jug (4):
100 ml MIN
150 ml MAX
Do not add more than that, otherwise the milk froth will overflow and soil the appliance.
▪ Place the lid (1) on the jug (4) and apply slight pressure to ensure a good seal.
▪ Press the Start/Stop button (5) twice until the symbol lights up blue. After around five seconds the
frothing starts automatically.
▪ After the programme ends, the appliance switches off automatically and the indicator light turns
off. Remove the lid (1) and skim off the milk froth separately, or pour it out with the remaining
milk.
Warning: Do not use any sharp metallic objects for skimming off the froth, as this can damage the
coating.
Hot milk
Select this programme to heat milk and slightly froth it. Hot milk is particularly suitable for milky
coffee, hot chocolate and cocoa.
▪ Add 100 to 250 ml of milk to the jug (4).
The filling marks are in the jug (4):
100 ml MIN
250 ml MAX
Do not add any more, as otherwise the milk will overflow and soil the appliance.
▪ Place the lid (1) on the jug (4) and apply slight pressure to ensure a good seal.
▪ Press the Start/Stop button (5) and hold for three seconds until the symbol lights up red and blinks.
After around five seconds the frothing starts automatically.
▪ After the programme ends, the appliance switches off automatically and the indicator light turns
off. Remove the lid (1) and pour the milk out.
13