Replacing The Battery; Charging The Battery; Led Indicators - Peg-Perego Polaris Rzr Pro Green Shadow Utilisation Et Entretien

side.
61 • Thread the battery plug and the electrical system
plug through the holes in the passenger's seat
base.
62 • Insert the seat base on the passenger side.
63 • Connect the battery and electrical system plugs.
64 • Fasten down the seat bases using 4 screws (two
on each side).
65 • Insert the two short sections of the safety belts
into the seat bases (in the holes near the gear
lever), taking care to insert all of the section of
belt highlighted in detail A. Note: the safety belt
buckle buttons must be facing the gear lever, as
shown in the figure.
66 • Unscrew the knobs from the seat base.
67 • Place the seat covers as shown in the figure.
68 • Position the seat. Note: the seat can be adjusted
in length to two different positions, depending on
the height of the child.
69 • Screw the knobs back into position.
70 • Lower the seat.
71 • Tighten the safety screw. Repeat for the other
seat.
72 • Install the two parts of the windshield as shown.
Picture A shows the grille fitted correctly
73 • Secure the grille with the three screws.
74 • Place the windshield on the hood hooking the
three central tabs.
75 • Fit the windscreen of the vehicle with screws
76 • Remove the protectors from the rear axle.
77 • Insert the axle into the rear of the vehicle, as
shown in the figure.
78 • Use a tool to attach the profiles to the wheel
rims, as shown in the figure.
79 • Place the driver in the inner part of one of the
four wheels.
80 • Assemble the wheel onto the axle with the driver
facing the vehicle. Pay attention to the direction
of the tread, as shown in the figure.
81 • Insert 1 small washer and 1 plastic washer onto
the axle.
82 • Fasten the wheel, tightening one of the four nuts
supplied with the spanner provided.
• Repeat the fitting operations for the other rear
wheel. Important: carry out the operations while
holding the axle still on the opposite side with
the help of the second spanner provided.
83 • Remove the steering lever protection caps.
84 • Insert a large washer onto the lever.
85 • Insert the bushing inside the wheel, paying
attention to the direction of the tread, as shown
in the figure.
86 • Fit the wheel you just assembled to the steering
lever.
87 • Insert a small washer onto the wheel.
88 • Fasten the wheel, tightening one of the two
remaining bolts with the spanner provided.
• Repeat the fitting operations for the front wheel
on the other side.
89 • Snap fit the four hub covers onto the wheels.
FEATURES AND USE OF THE VEHICLE
90 • 1- START/STOP: when pressed, this button lights
up and enables all the vehicle's functions (START).
When pressed again, it turns off and disables all
the vehicle's functions (STOP).
2 - FM RADIO:
A - USB port
B - SD CARD slot
C - AUX input
D - Selection buttons: when pressed individually,
these buttons allow you to select tracks and
radio frequencies.
When pressed several times simultaneously, they
allow you to shift from one mode to another, as
displayed (USB, SD, AUX ).
E - volume buttons: turn the volume down
completely to turn the radio off. The word OFF
will be displayed. Press the "volume up" button to
turn it on again.
3 - HORN: press it to activate it.
4 - ACCELERATOR PEDAL and ELECTRIC
BRAKE: lift the foot from the pedal to engage the
brake automatically.
The vehicle will enter standby mode (OFF) after
10 minutes of inactivity. If the START button is
activated, the vehicle will resume its functions by
pressing the pedal.
5 - LED indicators on the dashboard:
- ENGINE: a steady red LED indicates engine
overload. Release the pedal. Wait 10 seconds for
the vehicle to be ready for use again.
- BATTERY: a blinking orange LED means that the
battery is low. When this happens, the vehicle
enters "POWER SAVING" mode (low speed, no
lights and sounds).
The blinking LED becomes steady when the
battery is flat. At that point, the vehicle stops
working until the battery is charged. If you need
to move the vehicle while the battery is flat, you
can release the brake by pushing down the
accelerator. This way, you can push it manually.
6- Passenger handle.
91 • GEAR LEVER: when supplied the vehicle speed is
limited to first gear (1 - see figure). It also has a
reverse (R), and a second gear (2) recommended
only for expert drivers. To enable the second
gear, unscrew the red stop on the gear lever.
92 • Rotate the stop 90°, as shown in the figure, and
fix in position with the screw. Now by pulling
back the gear lever the vehicle can run in second
gear.
93 • DRINKS HOLDER - There are two drinks
holders for cans or bottles.
94 • REAR BOX and SUSPENSION - The rear of the
vehicle has a spacious cargo box and real
functional suspension on the wheels.
95 • SAFETY BELT - To fasten the safety belt, insert
the end of the longer belt section into the buckle
on the shorter belt section, pushing the two parts
together.
96 • To release the safety belt, press the buckle button
and at the same time separate the two elements.
97 • To change the length of the safety belt, move the
adjuster as shown in the figure.
98 • ACCESSORY: trailer to attach to the vehicle (sold
separately).

REPLACING THE BATTERY

PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
99 • Release the passenger seat safety screw and lift
the seat.
100 • Unscrew the knobs and remove the seat.
101 • Unscrew the two seat base screws. Disconnect
the battery and electrical system plugs.
102 • Extract the seat base and pull out the plugs.
103 • Replace the battery.
• Replace the seat base after passing the plugs
through the holes. Connect the plugs and
replace the seat.
104 • WARNING: always replace and tighten all the
knobs and screws.

CHARGING THE BATTERY

WARNING: BATTERY CHARGING AND ANY
OTHER WORK ON THE ELECTRICAL SYSTEM
MUST BE CARRIED OUT BY ADULTS.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
ATTENTION! Fully charge the battery
before using the toy.
• After every use or at least once every 3 months,
charge the lithium battery.
105 • Disconnect the electrical system plug A from
the battery plug B, pushing on the sides of the
plugs to release them.
106 • Plug the battery charger into a domestic power
outlet following the instructions enclosed with
it. Connect plug B to the battery charger plug
C.
107 • When charging is complete, disconnect the
battery charger from the domestic power
supply and then disconnect plug C from plug B.
108 • Fully insert plug B into plug A until it clicks into
position.
• WARNING: when the charging operations are
complete, always replace and tighten all the
knobs and screws.
109 • The battery can also be charged outside the
vehicle. This means that if you have a spare
battery, the child can continue to use the toy.
How to use the battery charger
WARNING
1 • Insert only lithium batteries supplied by PEG
PEREGO.
2 • Do not use with non-rechargeable batteries.
Risk of explosion.
3 • For adult use only. It is not a toy. This
appliance is not intended for use by infirm
persons unless they are being adequately
supervised by a responsible person to ensure
that they can use the appliance safely.
4 • Do not use with damaged sheathing, cable or
connector.
5 • Charge the battery only in a well ventilated area.
6 • Do not remove the plug by pulling on the cable.
7 • Do not drag the vehicle along on its wheels by
pulling the battery charger's cable.
8 • Avoid overheating the cable by covering it and
do not rest it on hot surfaces.
9 • Be aware of how the output cable is wound to
prevent damaging it.
10 • Should the battery charger be damaged, do not
use it until it is fully repaired.
11 • The product contains some elements that are
considered harmful to the environment. Disposal
of these elements or of the entire product at the
end of its life should be in accordance with the
regulations in force in the country where it is
used.
12 • Before using the battery charger make sure that
it is fitted with the specific plug for the country
in which it is going to be used.
13 • Children should not play with the battery
charger as IT IS NOT A TOY.

LED INDICATORS

Peg Perego Battery NOT connected
•GREEN LIGHT: the battery charger is working
correctly. It's in the socket, ready for operation.
Peg Perego Battery connected
•GREEN LIGHT: the battery is fully charged
•RED LIGHT: the battery is charging
The battery charger is fitted with a safety device
which means that in the event of overheating or a
short circuit of the battery, a protection system will
intervene to prevent current peaks, which could
damage the battery charger.
In this case unplug the battery charger from the
power outlet, remove the cause of the short circuit
and reconnect everything.