HYVA RM-081L/065L-059L-052L-MF Instructions De Montage
Table des Matières
Manuels Connexes pour HYVA RM-081L/065L-059L-052L-MF
Sommaire des Matières pour HYVA RM-081L/065L-059L-052L-MF
- Page 1 OIL TANK SLIM RM TANK MOUNTING INSTRUCTIONS...
-
Page 2: Table Des Matières
OIL TANK SLIM RM TANK Table of Contents PARTS FOR REAR MOUNTED – SLIM RM TANK ........................3 STEPS FOR MOUNTING AIR BREATHER..........................5 STEPS FOR MOUNTING RETURN LINE FILTER ........................6 STEPS FOR MOUNTING SLIM RM TANK ON SUPPORTS ......................8 SUCTION LINE COMPONENTS ASSEMBLY .......................... -
Page 3: Parts For Rear Mounted - Slim Rm Tank
OIL TANK SLIM RM TANK A. PARTS FOR REAR MOUNTED – SLIM RM TANK 1. TANKS & SUPPORTS No. Description Hyva - Oil tank – Slim RM Strap + Rubber strap Hex Nut M12 DIN 985 Rubber tank support Support Oil tank... - Page 4 OIL TANK SLIM RM TANK 2. AIR BREATHER No. Description Air breather Screw M5x14 ISO 2009 3. RETURN LINE FILTER PLATE VERSION HOUSE VERSION ADAPTER KIT No. Description Return line filter – House version Bolt for Return line filter – House version 2 / 4 Washer for Return line filter –...
-
Page 5: Steps For Mounting Air Breather
OIL TANK SLIM RM TANK B. STEPS FOR MOUNTING AIR BREATHER ➢ For part number refer to table on page 2, position 07 - 08 1. Remove sticker to assemble air breather & Return line filter 2. Assemble Air breather 1.5 Nm / 1.1 ft*lbf subject to change without notice OH-E OIL-0028 / 02-02-2021 / RV AA... -
Page 6: Steps For Mounting Return Line Filter
OIL TANK SLIM RM TANK C. STEPS FOR MOUNTING RETURN LINE FILTER ➢ For part number refer to table on page 2, position 09 - 17 1. Assemble Return line filter *20 Nm / 14.8 lbf*ft a. House version Return line filter *Note: Possibility of 2 or 4 bolts used. - Page 7 OIL TANK SLIM RM TANK c. Adapter with Plate version Return line filter *15 Nm / 11 lbf*ft subject to change without notice OH-E OIL-0028 / 02-02-2021 / RV AA...
-
Page 8: Steps For Mounting Slim Rm Tank On Supports
OIL TANK SLIM RM TANK D. STEPS FOR MOUNTING SLIM RM TANK ON SUPPORTS ➢ For part number refer to table on page 1, position 01 - 06 1. MOUNT THE VIBRATION DAMPERS UNDER THE SUPPORT *15 Nm / 11 lbf*ft 2. - Page 9 OIL TANK SLIM RM TANK 3. PLACE STRAPS & STRAP RUBBER ON TANK & MOUNT THE STRAPS 20 Nm / 14.7 lbf*ft 1000 km / 600 miles 4. SEE SUCTION HOSE SECTION FOR HOSE ASSEMBLY subject to change without notice OH-E OIL-0028 / 02-02-2021 / RV AA...
-
Page 10: Suction Line Components Assembly
OIL TANK SLIM RM TANK E. SUCTION LINE COMPONENTS ASSEMBLY SUCTION HOSE PARTS Description LP hose Hose clamp Hose clamp chassis MIN 1 Hose pillar straight Hose pillar 90 Ball valve subject to change without notice OH-E OIL-0028 / 02-02-2021 / RV AA... - Page 11 OIL TANK SLIM RM TANK 1. MOUNT THE SUCTION COMPONENTS 60 Nm / 44.2 lbf*ft 5 Nm / 3.7 lbf*ft 5 Nm / 3.7 lbf*ft 60 Nm / 44.2 lbf*ft Warning : Use 2 spanners to prevent over torquing in the pump or tank subject to change without notice OH-E OIL-0028 / 02-02-2021 / RV AA...
-
Page 12: Instruction
OIL TANK SLIM RM TANK F. INSTRUCTION • All parts should be free from dirt and burrs • All lines should be EITHER free OR clamped to prevent unsafe conditions during operation • All lines should be fitted without tension or too small bending radius •... - Page 13 OIL TANK SLIM RM TANK • Todas las piezas deben estar libres de suciedad y rebabas. • Todas las líneas deben estar libres o fijadas para evitar condiciones inseguras durante el manejo. • Todas las líneas deben instalarse sin tensión y el radio de flexión no puede ser demasiado pequeño. •...