Deca FL 1112 Manuel D'instruction page 7

Instruction manual.
Automatic battery charger
To identify your battery charger please refer to
Models illustrated on page 1
WARNING STICKER Fig.2
Before putting into operation for the first time,
attach the supplied sticker in your language
on the battery charger.
Carefully read this manual, and both the
instructions provided with the battery and
the vehicle in which it will be used before
charging.
Overview and warnings
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, if they have
been given supervision or instruction concerning.
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children
without supervision.
This battery charger can be used to charge lead-acid
batteries of the following types only:
D WET cells: Sealed, with liquid electrolyte inside. Low
maintenance or maintenance free (MF), "AGM", "GEL".
„ Never attempt to charge batteries that cannot be recharged
or other types than those indicated.
„ Never charge frozen batteries that might explode.
For indoor use only.
WARNING: EXPLOSIVE GAS!
„ Batteries generate explosive gas (hydrogen) during normal
operation and even greater quantities during recharging.
Avoid creating flames or sparks.
„ The battery charger has components such as switches
and relays that may create sparks. If the product is used in
a garage or similar places, position it adequately far from
the battery; it should not be inside the vehicle or the engine
compartment.
„ To avoid creating sparks, make sure that the clamps cannot
get detached from the battery terminals when the battery is
being charged.
„ Never let the cable clamps touch each other.
„ It is strictly forbidden to reverse polarity when you connect
the clamps to the battery.
Make sure that the plug is unplugged from the
socket before connecting or disconnecting the
cable clamps.
Provide adequate ventilation during charging
950603-03 10/09/14
EN
„ Always wear safety goggles closed at the sides, acid-proof
safety gloves, and acid-proof clothing.
„ Never use the battery charger with damaged cables or
whenever the charger has been subjected to impact or
damaged.
„ Never dismantle the battery charger: take it to an authorized
service centre.
„ Supply cable must be replaced by qualified people.
„ Never position the battery charger on flammable surfaces.
„ Never place the battery charger and its cables in the water
or on wet surfaces.
„ Position the battery charger with adequate ventilation; never
cover it with other objects or close it inside containers or
closed shelves.
Assembly and electrical connection Fig.5
¾ Put together the separate parts contained in the package.
¾ Make sure that there is a fuse or automatic circuit breaker for
the electric line, suitable for the device max input.
„ The device must be connected only to a supply system, with
an earthed 'neutral' lead.
¾ Supply plug: If the device does not have a plug, connect a
standardised plug of suitable capacity to the power supply
cable, (2P+E for 1Ph).
Battery charger description
Controls and indications Fig.1
A) ON/OFF switch.
B) 6 / 12 / 24 Volt selection button.
(2'' pressed) start / stop charging.
(5'' pressed) "Safe charge" disabled.
C) Output amps adjustment (charging current).
(2'' pressed) desulphation / equalisation programme
selection.
D) Charging Errors Led.
E) Charging step.
F) Charging step.
G) Desulphation / equalisation program seleted.
H) Output Fuse.
Connection of battery charger
Before starting the battery charger, make sure that the
battery voltage selected is the right one. Incorrect battery
voltage can damage objects and injure people.
To protect the electronic components on the vehicle,
carefully read the instructions by the car manufacturer
and the battery manufacturer before charging a battery
or using the Quick start procedure.
¾ Connect red charging clamp to positive (+) battery terminal and
black charging clamp (-) to negative battery terminal.
¾ If the battery is installed on a motor vehicle, first connect
the clamp to the battery terminal that is not connected to
the bodywork. Afterwards, connect the second clamp to the
bodywork at a point far from both the battery and the petrol
pipes.
¾ Plug the plug into the socket to begin charging.
6