Technical Data - KING CRAFT KCT 205 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Anleitung KCT 205
02.11.2001 9:12 Uhr
GB
Switch on the dust extraction system each time
you use the machine.
Use the saw only with a suitable vacuum
extraction system or a standard industrial
vacuum cleaner in order to prevent injuries
caused by flying pieces of wood.
The bench saw must be connected to a 230 V
socket-outlet with a minimum 10 A fuse.
Never use light-duty machines for heavy-duty
work.
Never use the cable for any purpose other than
that for which it is intended!
Adopt a firm standing position and keep your
balance at all times.
Check the tool for signs of damage!
Before you carry on using the tool it is imperative
to check that its safety devices and any slightly
damaged parts are working properly and in the
way intended.
Check that the moving parts work properly and
do not jam or whether any of the parts are
damaged. All parts must be fitted correctly and
satisfy all conditions for the tool to work properly.
Unless otherwise stated in these instructions,
damaged safety devices and parts must be
repaired or replaced by experts in an approved
specialist workshop.
Have damaged switches replaced by a customer
service workshop.
This tool complies with the pertinent safety
regulations. Repairs are to be carried out only by
qualified electricians using original replacement
parts. The user may suffer an accident if this
condition is not observed.
Wear goggles
Wear ear-muffs
Wear a breathing mask
Noise emission values
The saw's noise is measured in accordance with
DIN EN ISO 3744; 11/95, E DIN EN 31201;
6/93,ISO 7960 Annex A; 2/95. The machine may
exceed 85 dB(A) at the workplace. In this case,
noise protection measures need to be
introduced for the user (ear-muffs).
14
Seite 14
Sound pressure level LPA 105,0 dB(A) 85,0 dB(A)
Sound power level LWA
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immision level
at the workplace include the duration of impact, the
type of room, and other sources of noise etc., e.g.
the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."

5. Technical data

Asynchronous motor
Power rating
Idle speed n0
Carbide saw blade
Number of teeth
Table size
Cutting height max.
Height adjustment
Table tilt
Connector for dust extractor
Size, complete
6. Before putting the machine into
operation
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong stand.
All the covers and safety devices have to be
properly fitted before the machine is switched
on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Cutting
Idling
114,6 dB(A) 94,6 dB(A)
230 V 50 Hz
720 W S3 50%
2950 rpm
205 x 16 x 2.5 mm
20
500 x 420 mm
45 mm / 90°
27 mm / 45°
infinite 0 - 45 mm
infinite 0 - 45°
dia. 24 mm
500 x 420x 300 mm

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

43.406.10

Table des Matières