Inventronics OPTOTRONIC OT Wi 15/220-240/1A0 NFC BL LP I Mode D'emploi page 2

®
OPTOTRONIC LED Power Supply
Position 22)
24)
A or B
C
D

Installing and operating information: Connect only LED load type. LED
module will be switched off when output voltage is outside the voltage range
given on the driver. Wiring information (see fig. A): Do not connect the outputs of
two or more units. The metal surface on LED driver underside of OT Wi 40/220-
240/1A0 NFC BL LP I is double insulated against mains, also the metal surface
is SELV basic insulated against LED output. Output current adjustment = via
programming software using Near Field Communication (NFC) in mains off mode
only. For Near Field Communication (NFC) please refer to Tuner4TRONIC at
www.inventronicsglobal.com/t4t. Unit is permanently damaged if mains is applied
to the terminals 21/22. Lines 21/22 max. 2 m whole length excl. modules. Bluetooth
network reset: (1) Power off device and disconnect from mains, apply short circuit
between LED+ and LED-, (2) connect device to mains and power on for at least
2 seconds, (3) power off device, disconnect from mains and remove short circuit.
Reset completed. Emergency Lighting: This LED power supply complies with
EN 61347-2-13 Annex J and is suitable for emergency lighting fixtures according
to EN 60598-2-22 except those used in high-risk task areas. The device can be
put into operation using the HubSense Commissioning Tool version 1.30.1
(https://platform.hubsense.eu), subject to prior acceptance of the Terms of Use
and the Privacy Policy. Inventronics GmbH may terminate or suspend the use of
the HubSense Commissioning Tool at any time and for any or no reason in its
sole discretion, even if access and use is continued to be allowed to others.
Compatibility to future versions of the Hubsense Commissioning tool is not
guaranteed. The device complies with Bluetooth mesh Standard v1.0. It can also
be used in 3rd party Bluetooth mesh network, that complies with this standard
and that supports the mesh models of this device, and with certain 3rd party
commissioning tools, that support the mesh models of this device. In order to
ensure correct interoperability a verification with the 3rd party network components
and the 3rd party commissioning tool is necessary in advance. Please contact
the support (support@hubsense.eu) to receive the actual list of supported
2
Input / PRI
Output / SEC
Output / SEC
Cable types (tested acc. to EN 60598-1)
• NYM-J 3x1.5
• H05VV-F 3x1.5
• H05VV-F 2x1.5
• H05VV-F 2x1.0
• H05VV-F 2x1.5
• H05VV-F 2x1.0
• H03VV-F 2x0.75
• H03VV-F 2x0.5
• Style 21520
• H03VVH2-F 2x0.75
models for this device. Inventronics GmbH shall have no liability for any 3rd
party commissioning tool and does not make any representations, express or
implied, about the availability and/or performance of such commissioning tool.
Inventronics GmbH shall have no liability for and does not make any representa-
tions, express or implied, about the connectivity of Inventronics GmbH QBM
products with any other products. Hereby Inventronics GmbH declares that the
radio equipment types OT Wi 15/220-240/1A0 NFC BL LP I, OT Wi 25/220-240/700
NFC BL LP I and OT Wi 40/220-240/1A0 NFC BL LP I are in compliance with Direc-
tive 2014/ 53/ EU. The full text of the EU declaration of conformity is available at the
following internet address: www. inventronicsglobal .com.
NFC frequency range: 13 553 – 13 567 kHz; Bluetooth frequency range: 2400 -
2483.5 MHz; Max HF output power (EIRP) of the product: 4 dBm;
Technical support: www. inventronicsglobal .com
1) Qualified Bluetooth mesh compact LED driver for independent installation;
2) Constant current LED Power Supply; 3) wire preparation; push in; 4) t c point;
5) Made in Bulgaria; 6) picture only for reference, valid print on product; 7) Mains;
8) Input; 9) Output; 10) Year; 11) Week; 12) Safety note for mounting with metal
screw: The distance between the metal screw and the insulated single wires must
be at least 2.5 mm. 13) Mounting hint for proper radio connectivity. By integrating
the device into a casing the wireless range could be affected, in particular by
metal surfaces. Therefore, the wireless range needs to be verified after integration.
14) Do not place any mains voltage or LED supply wires within or close to this
area. 15) Recommended minimal distance to metal parts. 16) Placement of inte-
grated radio transmitter antenna; 17) Radio frequency; 18) Wireless protocol;
19) Qualified Bluetooth mesh; 20) Wireless range; 21) 10m line of sight; 22) Posi-
tion; 23) Cable types (tested acc. to EN 60598-1); 24) A or B
23)