Eno Enosign 65 Notice D'emploi Et D'entretien page 7

V. IGNITING YOUR PLANCHA
Burner is operated by a safety valve with FFO, equipped with an operating knob and an ignitor.
The knob bears an indication of valve position
- Open butane or propane cylinder or wall valve if using natural gas
- Your product is equipped with a locking valve in off position (Mark is clearly indicated with a full disk) giving a total security
- Press the knob and rotate it towards big flame (Sparkle symbol). Then operate the ignitor, a click can be heard and the
sparkle ignites the burner, keep the knob pressed during 10 seconds to action the security. Check that burner is well ignited
- Release the knob. If the burner does not remain ignited, start operation again. Then adjust the length of the falem ny rotating
the knob toward the small flame symbol. To shut the PLANCHA, rotate the knob toward off position (Full disk)
NOTICE: In case the igniter is not working properly, a hole in the front enables to ignite the burner with a long match.
Knob
Big flame
(Maxi output)
VI. BATTERY REPLACEMENT
- The battery holder is under the plancha, to replace it, remove the plate
and the lid, return the appliance and unscrew the black cap
anticlockwize, replace the 1,5V R6 type battery.
- Reassembly in the reverse mode.
- If you don't use your plancha for a long time, it is advisable to remove
the battery.
VII. MAINTENANCE OF YOUR PLANCHA
GREASE TRAY CLEANING : - To remove the grease tray, press above the
gauge until you hear a clik. You can clean the tray with dishwashing liquid or in
the dishwasher. Once its clean, introduce the tray in the reverse opposite
direction of disassembly.
Warm plancha : during cooking , let food grill for a few seconds until
slightly brown ; this is the so-said "Maillard Effect" caramelization of juices.
Unstick the food from the plate with the ENO spatula and turn it to
caramelize both sides. Then gently cook the food over low heat . You'll get
a juicy , slightly crunchy and very tasty cooking.
Between cookings : scrape the hotplate with the ENO spatula to remove
residues, scratch with the ENO stainless ball and wipe with an absorbing
cloth. Your plancha is ready for the following dish.
After cooking : before your plancha cools, scrape the hotplate with the ENO spatula. If the plate is very dirty, pour a little
water and scrape to remove residues. Use the ENO stainless ball to clean the hotplate and wipe with an absorbing
cloth.
Cold plancha : apply Plancha Cleaner with the stainless ball and a little water, then wipe with the ENO microfiber cloth
: your plancha will resume its original shine.
More user tips and recipes on YouTube PLANCHAENO
When you do not use any longer your PLANCHA, store it in a dry place or cover it with a plastic bag (Once it is completely cold)
Regularly check your hose. Do not hesitate to change it if any doubt (Check validity date)
Do not twist the gas hose and keep it away from any part that might be warm.
To remain in good condition, it requires a minimum care
Each product is checked all along manufacturing process.
If something un normal occurs, please check that all instructions have been
carefully respected. Especially check that the regulator used is corresponding
to gas and pressure from your cylinder and that the data badge on product is
corresponding to the gas you are using.
Not respecting these rules might damage your product.
If not used for a long period, check that burner venturi tube is not blocked.
1) Remove grilling plate
2) Unclip the burner cap
3) Check that burner is not blocked
If venturi tube is blocked, take the dirt away and
reaasemble the whole.
Off position
Adjustable foot
Small flame
(Mini output)
Battery Support
Igniter
Grease tray
1
3
2
CONTRACT GUARANTEE
In case of problem, contact the retailer whom you bought the Plancha from.
This product is guaranteed 2 years from date of purchase, against all manufacturing or operating failures.
Hotplate : lifetime guarantee
Burners : 10 years limited guarantee valid from date of purchase
During this guarantee, ENO after sales department takes the charge of cost of parts and labour to fix the product.
To operate this guarantee, you have to show the purchasing invoice and the guarantee sheet duly filled and bring the
product back to your retailer in its original packaging with a proper over packing.
Prior to the guarantee exercise, your retailer will have to give his formal agrement.
Battery
EXCLUSIONS OF GUARANTEE
This guarantee does not cover incidents due to a bad maintenance or faulty use : fall, shock, mistake in connection...
Guarantee of enamelled plate excludes damages resulting from following circumstances:
- Fall or shock
- Wrong use or not in conformity with users instructions
- Lack of maintenance or cleaning
- Use of corrosive detergents is not suitable with enamelled surfaces.
- Adaptation not complying with safety regulations
This guarantee is not applied if a person or company not duly entitled by ENO has made repairs or interventions.
Availability of parts is guaranteed during 5 years minimum.
Freight and packaging cost are taken over by customer. Returns carriage forward are not accepted. Once the product is
repaired, damages in transport are not covered by this guarantee. Les dommages subis pendant le transport des
appareils, une fois réparés, ne sont pas couverts par cette garantie. They must be confirmed by registered mail to the
Press above the gauge
transport company within 3 days. We cannot ensure a guarantee in case these prescriptions are not respected.
In case of dispute, the only recognized jurisdiction is the Court of Commerce in NIORT- FRANCE (This clause is
considered as essential without which, this guarantee should not exist).
LEGAL GUARANTEE
The dispositions of this guarantee do not exclude the benefit for the purchaser of the legal guarantee against defaults
and flaws which is generally applicable by law.
1
10