OPERATION
Correctly position item using only 1
laminating pouch per item.
For smaller or irregular shaped items, position item in center of adequate pouch and trim after lamination.
DO NOT CUT LAMINATING POUCH TO FIT ITEM BEFORE LAMINATION.
HOT LAMINATING
1. Insert the power plug into an electrical socket.
2. Push the control switch to "HOT
". The motor will start up and the red "POWER" indicator light
will turn on.
3. Wait 5-10 minutes for the machine to warm-up. The green "READY" indicator will light up when the
proper laminating temperature is reached.
4. Put the item being laminated into a laminating film leaving a 1/8"-3/8" border from the sealed
end of the pouch.
5. Insert them together into the feed entry at the front of the laminator.
Be sure to insert with the closed (sealed) edge of the laminating pouch first.
6. The finished laminated item will roll out through the exit slot on the back of the laminator.
7. Push control switch back to "OFF" to power off the laminator after use.
COLD LAMINATING
When switching over to the Cold lamination mode immediately after Hot laminating, please
wait at least 60 minutes for the laminator to cool down before use. If laminator is too hot
for Cold lamination, item being laminated could be damaged.
1. Insert the power plug into an electrical socket.
2. Push the control switch to "COLD
". The motor will start up and the red "POWER" indicator light
will turn on.
4. Put the item being laminated into a laminating film leaving a 1/8"-3/8" border from the sealed
end of the pouch.
5. Insert them together into the feed entry at the front of the laminator.
Be sure to insert with the closed (sealed) edge of the laminating pouch first.
6. The finished laminated item will roll out through the exit slot on the back of the laminator.
7. Push control switch back to "OFF" to power off the laminator after use.
4
CONTINUED ON NEXT PAGE
Item should be centered
Be sure to insert with the
within the pouch with a
closed (sealed) edge first
1/8"– 3/8" border.
OPERATION
When Finished Laminating:
Caution: When the laminated item exits, it may be very hot and soft. Handle the laminated item with care.
Pressing the item with a book or other heavy objects may help make it flat and smooth.
JAM RELEASE LEVER (CLEAR JAMMED ITEMS)
This laminator features a Jam Release lever to easily clear stuck items in the machine. Follow these steps:
• Turn off laminator and unplug from power outlet.
• Make sure laminator is on a stable flat surface.
• Firmly press the RED Jam Release lever all the way down and hold.
• With the other hand, pull to removing the jammed item from either the front or back opening.
• Release the Jam Release lever.
• When cleared, plug the power cord back into the outlet. Turn on and resume use.
• If laminator repeatedly jams, please contact the Customer Service center.
CARE AND CLEANING / STORAGE
Always unplug the laminator from electrical outlet and allow it to cool before cleaning. Do not use any
abrasive cleansers. With a clean damp cloth, simply use warm soapy water to wipe the exterior. Dry
thoroughly before storing or continued use. Never immerse the laminator in any form of liquid or under
running water.
DO NOT SPRAY OR KEEP ANY AEROSOL PRODUCTS IN OR AROUND THE LAMINATOR.
DO NOT USE CANNED AIR. Never use anything flammable to clean the machine. This may result
in serious injury or damage to the product.
DO NOT use any sharp or pointed articles for cleaning the inside, as this will damage the laminator.
Since deposits or residue will influence the laminating results, periodically clean the rollers after use.
While "ON", insert a folded letter-sized paper into the entrance of laminator. The paper will roll out
with any present residue. Repeat several times to completely clean the rollers. If the item being laminated
is jammed, turn off and unplug the machine and refer to "JAM RELEASE LEVER" in the Operations
portion of this user manual.
STORAGE
Always unplug the laminator from its outlet when not in use. Allow the laminator to completely cool
before storing. Store the laminator in a dry area. Never wrap the cord around the laminator since this
will contribute to the wear on the cord. Do not place heavy items on top of the laminator, which may
result in possible damage.
5