Krups EA876 INTUITION EXPERIENCE Mode D'emploi page 23

OTHER FUNCTIONS
HOW TO ACCESS YOUR MACHINE'S SETTINGS
Your KRUPS Intuition machine has many settings, do not hesitate to try them! This will allow you to personalise your experience
even more.
RÉGLAGES
LIST OF SETTINGS:
Language Selection of the language of your choice from 21 languages.
Setting the date is required, particularly if using an anti-limescale cartridge. Setting the time
Date and time
and 12 or 24 hour clock display
Screen brightness To adjust the screen brightness.
Light To activate or deactivate the intuitive indicator light.
Choice of 1st
Choose the presentation of the first screen.
screen
To choose the duration after which your appliance will stop automatically. This function allows
Auto stop
you to consume less electricity.
To turn on the machine and automatically start preheating the appliance at a chosen time. Do
Auto illumination
you always have your coffee at the same time each day? This feature is made for you! By setting
the auto start, you can save time and only have to start your drink.
Volume unit
Selection of the unit of measurement: ml or oz.
You can choose to activate automatic rinsing of the coffee outlet or not when starting the
Auto rinsing
machine.
To adjust the hardness of the water between 0 and 4. For more information, refer to the chapter
Water hardness
"Measuring water hardness".
Coffee
To set the temperature of your coffee between T1 and T3.
temperature
Tea temperature To set the temperature of your tea between T1 and T3.
Type of coffee Indicate the type of coffee added in the bean container.
ANSWERS TO YOUR QUESTIONS
OPERATION
1. The machine displays a fault, the software is frozen OR the machine is malfunctioning.
Turn off and unplug the machine, remove the filter cartridge, wait 1 minute and restart the machine.
Press and hold the ON/OFF button for at least 3 seconds to start.
2. The appliance does not turn on after pressing the ON/OFF button (for at least 3 seconds).
Check the fuses and the power socket of your electrical installation. Check that the two power plugs are correctly inserted into
the socket.
3. A power failure has occurred during a cycle.
The appliance resets automatically when it turns back on.
40
4. The grinder is running empty.
This is normal if it happens occasionally and if there are no coffee beans or only a small amount. It can run for up to
10 seconds off-load to know its consumption and ensure the correct operation of its function
Coffee beans remain in the container:
• The coffee may be too oily and is therefore not being correctly captured by the appliance. You could try helping the
beans to go down and see if that gets it working again. However, it is advisable to change coffee (ref. type of beans
function).
• This is my usual coffee that has worked well until now: contact your KRUPS consumer service.
USE
1. The grinder makes an abnormal noise.
Foreign bodies are likely to be present in the grinder. Try to clean out with a vacuum cleaner, otherwise contact your KRUPS
consumer service.
2. There is water under the appliance.
Before removing the drip tray, wait 15 seconds after the flow of coffee so that the machine finishes its cycle correctly.
Check that the drip tray is well positioned on the machine. It must always be in place even when the machine is not in use.
Verify that the drip tray is not full.
3. The adjustment button for the grinding fineness is difficult to turn.
Turn the adjustment button of the grinding fineness only when the grinder is operating.
4. The appliance has not delivered any coffee.
An incident has been detected during its making.
The appliance is reset automatically and is ready for a new cycle.
5. You have used ground coffee instead of coffee beans.
Use your vacuum cleaner to collect the ground coffee from the bean container.
6. Water runs from the coffee nozzles when the machine stops.
This is normal. It is an automatic rinsing process to clean the coffee nozzles and ensure that they do not become blocked
STEAM AND MILK
1. The milk flow of your machine appears to be partially or completely blocked.
Refer to the beginning of the manual at 5. IN-DEPTH MANUAL CLEANING OF THE MILK DISTRIBUTION SYSTEM - 5 MIN., or
see the tutorial saved in your machine "Cleaning the milk nozzle".
2. No steam comes out.
a. When using a steam cycle for the first time, if no steam comes out correctly:
Check that the steam output is not blocked. See above: "The steam output of your machine appears to be partially or
completely blocked".
Perform the following process once only :
Empty the water tank and temporarily remove the Claris Aqua Filter System cartridge. Fill the tank with mineral water
high in calcium (>100 mg/L) and make successive steam cycles (5 to 10 cycles) in a container until a continuous jet of
steam is obtained. Return the cartridge to the reservoir.
b. The steam nozzle had already worked:
Check that the steam output is not blocked. See above: "The steam output of your machine appears to be partially or
completely blocked".
If after completing the above steps it still does not work, please contact your KRUPS consumer service.
3. Steam escapes from the grid of the drip tray.
Depending on the type of preparation, steam may escape from the grid of the drip tray.
4. Steam appears under the bean tray lid.
Check that the cleaning tablet hatch located under the lid (L) is properly closed.
MAINTENANCE
1. The machine does not request descaling.
The descaling cycle is requested from a large number of milky drink preparations or hot water. If you only consume coffee,
descaling will not be required often.
2. Some grounds are in the drip tray
A small amount of ground coffee can get into the drip tray. The machine is designed to evacuate any excess ground coffee
so that the percolation zone remains clean.
3. The intuitive indicator light is still on after you have emptied the coffee grounds tray.
Reinstall the coffee grounds tray.
41