Table des Matières
Publicité
Attention! Do not operate the
smoke generator with the smoke
stack lid closed. If the lid is closed
while the smoke generator is ope-
rated, the loco will be seriously
damaged.
Attention! Only use LGB Smoke
and Cleaning Fluid (50010) in the
smoke generator. Other fluids
may damage your locomotive.
Attention! Never touch the hea-
ting element in the center of the
smoke generator. It is fragile.
Power Supply
Attention! For safety and reliabi-
lity, operate this model with LGB
power supplies (transformers,
power packs and controls) only.
The use of non-LGB power sup-
plies may void your warranty.
For more information on LGB
power supplies for indoor, outdoor
and multi-train operation, see the
LGB catalog.
Attention! After extended opera-
tion, this model may leave a small
amount of carbon dust around the
track. This dust can stain carpet
and other materials. The user
assumes full responsibility for any
damage.
MAINTENANCE
Attention! Improper service may
void your warranty. For factory
authorized service, contact an
authorized retailer or send this
LGB product to an LGB service
station (see Factory Service).
Lubrication
The axle bearings and drive rod
ends should be lubricated occa-
sionally with a small amount of
LGB Maintenance Oil (50019).
Cleaning
This model can be cleaned using
a mild detergent and gentle stre-
am of water. Do not immerse this
model. If this model is equipped
with sound electronics, do not
expose the speaker directly to
water.
Replacing the light bulbs
Front lanterns: Pull the lantern
housing away from the model.
Remove and replace the bulb.
Reassemble.
Rear lanterns: Remove the ring
around the lantern lens. Carefully
pry the lens away from the lan-
tern. Using tweezers, remove and
replace the bulb. Reassemble.
Cab light: Using tweezers, remo-
ve and replace the bulb.
Replacing the traction tire
- Use a small, straight-blade
8
screwdriver to gently pry the old
traction tire out of the wheel
groove.
- Gently warm the new traction
tire in a dish of warm water.
- Use a small, straight-blade scr-
ewdriver to gently pry the new
traction tire into the wheel groo-
ve.
- Make sure that the traction tire is
completely in the wheel groove.
Replacing the motor
- Remove the hex head screws
joining the drive rods to the
connecting rods on the third axle
(Fig. 2).
- Counting from the front, remove
the first, second and fifth screw
on the bottom of the gearbox.
- Remove the gearbox from the
chassis. Disconnect the wiring
cable.
- Remove the top of the gearbox
by removing two screws. Repla-
ce the motor.
- Reassemble.
Attention! If the motor is repla-
ced, generously lubricate the
gears with LGB Gear Lubricant
(51020).
Attention! If the motor is repla-
ced, make sure that the drive rods
do not bind. Binding can cause
serious damage to the model.
Replacing the brushes, pick-up
shoes and wheelsets
Remove the five screws on the
bottom of the gearbox (Fig. 2).
Remove the bottom of the gear-
box. If necessary, replace the
brushes, pick-up shoes or wheel-
sets. Reassemble.
Attention! If the wheelsets are
replaced, generously lubricate
the gears with LGB Gear Lubri-
cant (51020).
Attention! If the wheelsets are
replaced, make sure that the drive
rods do not bind. Binding can
cause serious damage to the
model.
Maintenance parts
50019 Maintenance Oil
50020 Special Tool Set
55020 Multi-Train System
Decoder
55026 Decoder Interface Cable
62201 Standard Motor
63120 Brushes, 14 mm, 16
mm, 8 pack
63218 Standard Pick-Up
Shoes, 2 pack
68511 Plug-In Bulb, Clear, 5
volt, 10 pack
69104 Traction Tire, 37.5 mm,
10 pack
Publicité
Table des Matières
