Combi L; Activating The Control Unit; Uv Hygiene Management (Optional) - DURAVIT Combi L Notice D'utilisation

3. Combi L

aCTIVaTINg ThE CONTROL UNIT

Touch the control unit. It lights up in blue and is now activated. Now you
can start the desired function by pressing a button softly.
SwITChINg ThE aIR NOZZLES ON aND OFF
> Press the "Air" button. The air nozzles are switched on.
> Press the "Air" button a second time. The interval timer is activated.
> Press the "Air" button a third time. The air nozzles are switched off.
SwITChINg ThE JET NOZZLES ON aND OFF
Prerequisite: Water level of min. 5 cm above the topmost whirling nozzle.
> Press the "Jet" button. The water jet massage is switched on.
> Press the "Jet" button a second time. The air / water jet is activated.
> Press the "Jet" button a third time. The interval-controlled air / water
jet is activated.
> Press the "Jet" button a fourth time. The jet nozzles are switched off.
SwITChINg ThE ROTOJET NOZZLES ON aND OFF
The jet nozzles are switched on in addition to the foot or back massage.
Adjust the massage jet direction by means of the „Jet" button.
Switching the foot massage on and off
Prerequisite: Water level of min. 5 cm above the topmost whirling nozzle.
> Press the "Foot massage" button. The foot massage and jet nozzles
are switched on.
Switching the back massage on and off
Prerequisite: Water level of min. 5 cm above the topmost whirling nozzle.
> Press the "Back massage" button. The back massage and jet nozzles
are switched on.
aDJUSTINg ThE INTENSITy OF ThE MaSSagE
Prerequisite: The desired nozzle is switched on.
> Press the "+" or "-" button. The intensity increases or decreases. A
longer beep can be heard when reaching the highest or lowest level.
In case of Combi L with temperature model, the selected level ap-
pears in the display.
aDJUSTINg ThE DIRECTION OF ThE MaSSagE JET
> Turn the ball of the jet or rotojet nozzle until the direction of the mas-
sage jet is the most agreeable for you.
9
BAL_53481/10.10.3
SwITChINg ThE ILLUMINaTION ON aND OFF
Switching the coloured light on and off (optional)
CaUTION! Never look directly into the lights.
> Press the "Light" button. A white illumination is switched on.
> Press the "Light" button a second time. The light changes with smooth
transition every 10 seconds using a sequence of six colours.
> Press the "Light" button a third time. The presently shown colour is
fixed.
> Press the "Light" button a fourth time. The light is switched off.
Switching the halogen lamp on and off
> Press the "Light" button.
SwITChINg ThE TEMPERaTURE MODEL ON aND OFF
If you switch on the temperature model, the jet nozzles will start auto-
matically.
Switching the temperature model on and off
Prerequisite: Water level of min. 5 cm above the topmost whirling noz-
zle.
> Press the "Temperature" button. The jet nozzles are switched on.
Selecting the temperature
Prerequisite: The temperature model is activated.
> Press the "+" or "-" button. The desired temperature is displayed
(30 °C to max. 42 °C); after a period of 4 seconds, the display shows to
the actual temperature.

UV hygIENE MaNagEMENT (OPTIONaL)

If you have selected the optional module UV hygiene management, the
water is automatically exposed to UV radiation when activating the jet
nozzles thus preventing the formation of bacteria and germs. Therefore,
the jet nozzles should run minimum two to three minutes when having
a bath.
9
BAL_53481/10.10.3