Jet L - DURAVIT Combi L Notice D'utilisation

4. Jet L

aCTIVaTINg ThE CONTROL UNIT
> Touch the control unit.
It lights up in blue and is now activated. Now you can start the desired
function by pressing a button softly.
SwITChINg ThE JET NOZZLES ON aND OFF
water jet massage
Prerequisite: Water level of min. 5 cm above the topmost whirling nozzle.
> Press the "Jet I" button. The water jet massage is switched on.
> Press the "Jet I" button a second time. The interval-controlled water
jet is activated.
> Press the "Jet I" button a third time. The jet nozzles are switched off.
air / water jet massage
Prerequisite: Water level of min. 5 cm above the topmost whirling nozzle.
> Press the "Jet II" button. The water jet massage is switched on.
> Press the "Jet II" button a second time. The air / water jet is activa-
ted.
> Press the "Jet II" button a third time. The interval-controlled air / wa-
ter jet is activated.
> Press the "Jet II" button a fourth time. The jet nozzles are switched
off.
SwITChINg ThE ROTOJET NOZZLES ON aND OFF
The jet nozzles are switched on in addition to the foot or back massage.
Adjust the massage jet type by means of the „Jet II" button.
Switching the foot massage on and off
Prerequisite: Water level of min. 5 cm above the topmost whirling nozzle.
> Press the "Foot massage" button. The foot massage and jet nozzles
are switched on.
Switching the back massage on and off
Prerequisite: Water level of min. 5 cm above the topmost whirling nozzle.
> Press the "Back massage" button. The back massage and jet nozzles
are switched on.
aDJUSTINg ThE INTENSITy OF ThE MaSSagE
Prerequisite: The desired nozzle is switched on.
Press the "+" or "-" button. The intensity increases or decreases. A lon-
ger beep can be heard when reaching the highest or lowest level. In
case of Jet L with temperature model, the selected level appears in the
display.
10
BAL_53481/10.10.3
aDJUSTINg ThE DIRECTION OF ThE MaSSagE JET
Turn the ball of the jet or rotojet nozzle until the direction of the massage
jet is the most agreeable for you.
SwITChINg ThE ILLUMINaTION ON aND OFF
Switching the coloured light on and off (optional)
CaUTION! Never look directly into the lights.
> Press the "Light" button. A white illumination is switched on.
> Press the "Light" button a second time. The light changes with smooth
transition every 10 seconds using a sequence of six colours.
> Press the "Light" button a third time. The presently shown colour is
frozen.
> Press the "Light" button a fourth time. The light is switched off.
Switching the halogen lamp on and off
> Press the "Light" button.
SwITChINg ThE TEMPERaTURE MODEL ON aND OFF (OPTIONaL)
If you switch on the temperature model, the jet nozzles will start auto-
matically.
Switching the temperature model on and off
Prerequisite: Water level of min. 5 cm above the topmost whirling noz-
zle.
> Press the "Temperature" button. The jet nozzles are switched on.
Selecting the temperature
Prerequisite: The temperature model is activated.
> Press the "+" or "-" button. The desired temperature is displayed
(30 °C to max. 42 °C); after a period of 4 seconds, the display shows to
the actual temperature.
UV hygIENE MaNagEMENT (OPTIONaL)
If you have selected the optional module UV hygiene management, the
water is automatically exposed to UV radiation when activating the jet
nozzles thus preventing the formation of bacteria and germs. Therefore,
the jet nozzles should run minimum two to three minutes when having
a bath.