Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
1. The junction box or Infinite WaterColors LED Light
Controller suitable for direct conduit connection to
lights must be located at least (8) inches above water
level, at least four (4) inches above ground level, and
at least (48) inches (4) feet from the edge of the pool,
or as required by local code, see Figure 1 .
2. The light fixture and all metal items within five
(5) feet of the pool must be properly electrically
bonded to a reliable point of grounding.
3. The wet niche must be properly installed so that the
top edge of the underwater light's lens is at least
(18) inches below the surface of the water in the
pool. See Figure 1 .
4. The wet niche must be properly electrically bonded
and grounded via the No. 8 AWG ground connector
located at the rear of the niche. See Figure 1 .
National Electrical Code
of the Pool Water. Where none of the bonded
pool equipment, structures, or parts are in direct
connection with the pool water; the pool water shall
be in direct contact with an approved corrosion-
resistant conductive surface that exposes not less than
5800 mm² (9 in²) of the surface area to the pool water at
all times. The conductive surface shall be located where
it is not exposed to physical damage or dislodgement
To GFCI, Circuit Breaker
and Power Source.
Rigid
Conduit
Figure 1. Jandy Infinite WaterColors Light Installation
2.2
Installing the Light Fixture
NOTE: Perform these steps only after the electrical system
requirements are met.
1. Feed cord through conduit to junction box, leaving
at least four (4) feet of cord at the light fixture to coil
into the base of the light niche, see Figure 1 . The
four (4) feet of cord allows the light to be serviced
after the pool is filled with water.
2. Cut the cord at the junction box, leaving at least six
(6) inches of cord to make connections.
Page 4
Jandy
Infinite WaterColors
®
(NEC
) requires bonding
®
®
48"
min.
Check AHJ and local code for
additional requirements.
4" min.
#8 AWG Ground
Connector bonding
is located at rear of
niche.
Pool & Spa LED Lights | Installation & Operation Manual
™
during usual pool activities, and it shall be bonded in
accordance with the bonding requirements of NEC
Article 680. Refer to locally enforced codes for any
additional pool and spa bonding requirements.
NOTE: To be certain that the pool's electrical system meets
all applicable requirements, the electrician should also
consult the local building department.
Use only approved wet niches (see following note) to
ensure a safe and proper installation.
NOTE: Jandy lights are ETL listed for installation with only the
following manufacturer's wet niche fixtures:
Large Niche Model Numbers:
Jandy: PLNICLRG, PLNICVFLRG, WT000002,
SSNICLRG1R, SSNICLRG1S
Pentair
: 620004, 78210200 thru 700, 78210401
®
Hayward
DuraNiche: SP0600U
®
Small Niche Model Numbers:
Jandy: PLNICSM, SSNICSM,
Pentair: 79206600
8" min. Junction Box or Infinite
WaterColors LED Light Controller, to
the max water level of the pool.
18" min. to top of lens.
Concrete must be cut back
around niche to allow for a
compacted plaster seal.
11.50"
Coil 4 ft. of light cable
around fixture.
16"
3. Strip six (6) inches of the outer cord jacket to
expose the three insulated wires. Be careful not to
damage the insulation on the three (3) inner wires.
4. Install strain relief over cord jacket and connect the
light wires to the controller, black to orange, white
to orange, and green to the ground terminal bar.
Install the junction box cover.
5. Coil the 4-foot length of cord around the fixture or
into the base of the pool niche, and place the light
assembly into the niche.
Publicité
