Air Naturel Air&me Lendou Guide D'utilisation page 10

MAINTENANCE AND FILTER REPLACEMENT (SEE PAGE 3)
• Make sure the unit is turned off and unplugged before any manipulation.
• Do not immerse the device in water or any other liquid.
• Do not use corrosive, abrasive or flammable products to clean the unit.
• The particulate filter is not washable and needs to be replaced.
CLEANING THE FABRIC PRE-FILTER
Removable fabric pre-filter captures dusts and animal hair and dander. It is to be washed
about every 15 days, in order to guarantee the effectiveness of the purifier. You can wash it
with a vacuum cleaner along with a soft brush. You can also put it in the washing machine, on
a program for "delicate fabrics".
Caution: Don't iron the pre-filter. Never place a pre-filter that is still wet on the device. Only the
pre-filter is reusable and can be cleaned with water.
AIR INLET AND OUTLET OF THE DEVICE
The air is aspired from the back of the unit and comes out at the top. Use a soft cloth to remove
dust from the air inlets and outlets.
FILTER REPLACEMENT
Thanks to OptiFilter technology, an indicator light turns on when the filter has to be replaced
TM
(every 6 to 12 months). To replace the filter:
Make sure the unit is unplugged, then remove the pre-filter from the unit and unclip the rear
1
grille.
Gently pull the two tabs on the used filter out of the machine.
2
Place the used filter directly in a bag and throw it quickly to avoid dispersing contaminants.
3
Carefully install the new filter, placing both tabs facing you.
4
Replace the rear grille and the pre-filter.
5
Reconnect and turn on the device.
6
Press the [ Filter ] button for 3 seconds to reset the filter wear measurement system.
7
Avoid used filters being handled by people with asthma or allergies. Remember to wash your
hands after handling a used filter.
CLEANING THE AIR QUALITY SENSOR
The particle sensor requires regular dusting: every 2 months, depending on the frequency of
use and the environment in which the device is placed. To do this, use a vacuum cleaner to
capture any dust.
Caution: Do not use detergents, corrosives or metal objects to clean the sensor. The efficiency
of the sensor is susceptible to decrease if it's not cleaned regularly.
STORAGE OF THE DEVICE
If you don't use your air purifier, you can store it in a clean place, away from moisture and heat.
18
FAQ
Problem Reason
> The product is not correctly
plug or there is an electrical
problem.
> There is a problem on the
The appliance
electrical system of your
does not work
house.
> The filter and/or the
rear grille is not properly
engaged.
> The pre-filter is dirty, which
hinders the airflow.
Drop in the
> The air inlet or outlet is
appliance
blocked by something.
performance
> The air quality sensor is dirty.
> Something obstructs the
fan.
> The device has a
functioning problem.
Abnormal noise
> The filter is dirty.
The appliance
> The air inlet or outlet is
does not
obstructed.
produce air
The air coming
> The filter needs to be
out of the
cleaned or replaced.
appliance smells
bad
> The air quality sensor is dirty.
The color of
> You are not in a very
the air quality
polluted environment.
indicator doesn't
change
> The filter must be replaced
if the light remains red.
Solution
> Plug the socket correctly and
check the voltage and the good
functioning of your electrical
system.
> Push and engage the grille
correctly.
> Clean the pre-filter
> Leave at least 50 cm space
behind, on the sides and in front
of the unit.
> Please see "Maintenance"
paragraph.
> Make sure that no object
obstructs the air flow.
> Contact your reseller for service
support.
> Please see "Maintenance/
Replacement of the filter"
paragraph.
> Please see "Maintenance"
paragraph and make sure no
objects are blocking the airflow.
> Please see "Maintenance/
Replacement of the filter"
paragraph.
> Please see "Maintenance"
paragraph.
> To change to orange or red, the
ambient air must be polluted.
> Please see "Maintenance"
paragraph.
19