Playing Cds/Mp3; Listening To The Radio - AEG SR 4353 CD/MP3 Mode D'emploi

English
36
Amplifying bass
Press the BASS switch (23) to turn the bass amplification on or
off.
Switch-off
he machine is switched off when the function selector switch
(26) is turned to the TAPE OFF position. The POWER (24)
control lamp goes off. Unplug the device.
NOTE:
After approx. 15 minutes without a signal, the device will
automatically switch to standby. To use the device again,
press the / button (10).
AUX IN jack
1. Connect the 3.5 mm stereo RCA cable to an external
audio source. If required, use a suitable adapter (not
included).
2. Insert the other end of the cable into the AUX-IN jack
(Back Side) on the unit.
3. Set the function selector switch (26) to the "CD/MP3/
AUX" position.
4. Start the playback of your audio source. Listen to the
sound playback via the speaker.
5. For the further procedure, please refer to the user manual
of the external audio source.
NOTE:
If possible, adjust the volume of the external unit to a com-
fortable level.

Listening to the Radio

1. Set the function selector switch (26) to the "RADIO" posi-
tion.
2. Select the desired frequency band with the band selector
switch (3).
VHF (Stereo) = FM.ST, Medium wave = AM (Mono)
2. Tune in the desired station with the station adjustment
knob TUNING (5).
3. The FM ST. indicator lamp (19) will only be lit, when the
station is received in stereo quality. If reception is too
weak and there is noise on the station being received,
this lamp will flicker.
4. For FM mode pull out the telescopic antenna (6) and turn
it to improve reception.
5. An aerial is integrated into the device for the reception of
AM stations. The machine can be aligned to the station
by turning it. In this frequency band programs are trans-
mitted in "mono" only.

Playing CDs/MP3

This is how you play a CD
1. Turn the function selector switch (26) to the "CD/MP3/
AUX".
2. Open the CD tray (2) by pressing the PUSH TO OPEN
button (7).
3. Insert an audio CD with the printed side facing upwards
on to the central cone so that the CD clicks into place
and then close the lid of the CD compartment.
4. After a few seconds the total number of songs/tracks is
shown in the display.
NOTE:
In the case of CDs in MP3 format the number of folders
is briefly displayed at first.
5. Press the / button (10) to restart playback. The CD
will play from the first title. The current track and the "CD
" or "MP3 " message are shown on the display.
NOTE:
With CDs in MP3 format the current track and folder
are shown alternately in the display.
6. In order to remove a CD, please press the button (11),
open the CD compartment and lift the CD out carefully.
Always keep the CD deck closed.
NOTE:
• If a disc is inserted the wrong way, or if no disc is
inserted, the message "– – –" will flash and "NOd" will
appear on the display.
• Playback of CDs produced by the user cannot be
guaranteed due to the large variety of software and CD
media available.
Description of the CD buttons
/ (10)
You can briefly interrupt and resume playback using this but-
ton. The symbol " " flashes on the display. Pressing again
continues playback.
/ (9/8)
When playing an audio CD or a CD in MP3 format:
With you can jump to the next or previous track etc.
• If the button is kept pressed down, the machine starts to
search through the tracks.
The button can be used as follows:
Press once = This jumps back to the previous track.
Press twice = This plays the song before etc. If the button
is kept pressed down, the machine starts to
search through the tracks.