1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. CP0493
  6. Instructions de montage

R&G CP0493 Instructions De Montage

Masquer les pouces
1
2
3
4
5
6
7
8
9

Table des Matières

Page 1 of 13
CP0493
FITTING INSTRUCTIONS FOR CP0493 AERO CRASH PROTECTORS
FOR BMW S1000 XR 2020-
PICTURE A
PICTURE B
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF
OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE
.
WAY OF MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Table des Matières
loading

Manuels Connexes pour R&G CP0493

Sommaire des Matières pour R&G CP0493

  • Page 1 Page 1 of 13 CP0493 FITTING INSTRUCTIONS FOR CP0493 AERO CRASH PROTECTORS FOR BMW S1000 XR 2020- PICTURE A PICTURE B HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY...

  • Page 2: Tools Required

    Page 2 of 13 CP0493 TOOLS REQUIRED GENERAL TORQUE SETTINGS • M4 BOLT = 8Nm Socket set to include 17mm A/F socket and wrench. M5 BOLT = • Torque wrench (up-to 40Nm). M6 BOLT = M8 BOLT = 20Nm 0 BOLT = 40Nm...
  • Page 3 Page 3 of 13 CP0493 LEFT-HAND SIDE ASSEMBLY RIGHT-HAND SIDE ASSEMBLY R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...

  • Page 4: Fitting Instructions

    Page 4 of 13 CP0493 AERO STYLE CRASH PROTECTOR ORIENTATION PICTURE C PICTURE 1 PICTURE 2 FITTING INSTRUCTIONS Near side (left side as you sit on the motorcycle) • Place one of the M10 plane washers (item 3) onto one of the M10 hex bolts (item 2) followed by one of the shake proof washers (item 4) as shown in the left-hand side assembly picture.
  • Page 5 Page 5 of 13 CP0493 Off side (right side as you sit on the motorcycle) • Place one of the M10 plane washers (item 3) onto one of the M10 hex bolts (item 2) followed by one of the shake proof washers (item 4) as shown in the right-hand side assembly picture.
  • Page 6 Page 6 of 13 CP0493 NOTICE DE MONTAGE POUR CP0493 PROTECTIONS CRASH POUR BMW S1000 XR 2020- PHOTO A PHOTO B E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES...
  • Page 7 Page 7 of 13 CP0493 TOOLS REQUIRED VALEURS DE SERRAGE • M4 BOULON = 8Nm Clé à cliquet + douille 17mm. M5 BOULON = • Clé dynamométrique (40Nm). M6 BOULON = M8 BOULON = 20Nm 0 BOULON = 40Nm M12 BOULON = 40Nm LÉGENDE...

  • Page 8: Assemblage Côté Droit

    Page 8 of 13 CP0493 ASSEMBLAGE CÔTÉ GAUCHE ASSEMBLAGE CÔTÉ DROIT R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...

  • Page 9: Côté Gauche (Lorsqu'on Est Assis Sur La Moto)

    Page 9 of 13 CP0493 NOTICE DE MONTAGE Côté gauche (lorsqu’on est assis sur la moto) • Placer l'une des rondelles plates M10 (article 3) sur l'un des boulons hexagonaux M10 (article 2) suivi de l'une des rondelles anti-vibration (article 4) comme indiqué...

Table des Matières