Bosch GHJ 12+18V Men Professional Notice Originale page 11

OBJ_BUCH-2969-001.book Page 11 Thursday, September 22, 2016 11:38 AM
Technical Data
Heated jacket
Article number
Sizes
Voltage
Battery Adapter
Article number
USB port
– Charging voltage
– Charging current
Battery
Permitted ambient temperature
– during charging
*
– during operation and during storage
Recommended batteries
Recommended chargers
* limited performance at temperatures <0 °C
Preparing the Garment
Battery Charging
 The battery adapter does not serve as a charger. Do not
use any vehicle charging cables with USB connection to
charge the battery. Using vehicle charging cables can
damage the battery and/or the battery adapter.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". The heating ele-
ments are switched off by a protective circuit when the bat-
tery is discharged.
 Do not continue to press the on/off switch after the
heating elements have been automatically switched
off. The battery can be damaged.
Battery Insertion/Removal (see figures A1 – A2)
 Do not use force to insert the battery. The battery is de-
signed in such a way that it can only be inserted into the
battery adapter when it is in the right position.
– To insert the battery 7, slide it all the way into the battery
adapter 2.
– To remove the battery 7, press the unlocking buttons 8 on
the battery and pull it out of the battery adapter 2.
Bosch Power Tools
Connecting the Heating Elements
(see figures B1–B2)
GHJ 12+18V Men
– Plug the connector plug 4 into the socket 9 on the battery
GHJ 12+18V Women
1 600 A00 Y..
XS/S/M/L/XL/2XL/3XL
V 12
– Slide the battery adapter 2 into the pocket 5 provided in
GAA 12 V
0 618 800 002
Using the Garment
USB 2.0
V 5.0
A 1.0
Starting and Stopping (see figure C)
– Ensure that the battery 7 is charged and correctly inserted
°C 0...+45
– To heat, press the on/off switch 1 until the LED of the
°C –20...+50
GBA 10,8V..
Note: The heating is always set to the highest heating level af-
GBA 12V...
ter it is switched on.
AL 11.. CV
– To switch off, press the on/off switch 1 until the LED goes
GAL 12.. CV
Setting the Heating Level
The heating level is indicated by the colour of the LED on the
on/off switch 1.
LED
red
green
blue
– Repeatedly press the on/off switch 1 until the LED displays
 Set the lowest heating level (blue) for continuous oper-
Charging External USB Devices (see figure D)
You can use the USB port on the battery adapter to increase
the battery runtime of various battery-operated USB devices,
e.g. mobile phone or MP3 player.
This can also be done whilst the garment is being heated.
 Ensure that your external USB device can be charged
– Connect the charging cable of your USB device to the USB
– Press the activation button 12 for approx. 3 seconds.
To save energy, the USB port is automatically deactivated af-
ter approx. 2 hours.
If no charging cable is connected, the USB port is automatical-
ly deactivated after 30 seconds.
adapter.
If the battery is charged, the on/off switch 1 will light up
briefly.
the garment or hang the battery adapter on your belt using
the belt clip 10.
into the battery adapter 2 and that the heating elements 3
are connected.
on/off switch lights up red.
out.
Thermal output
high
medium
low
the required heating level.
ation. In the event of overheating, there is a risk of garment
malfunction and of injury.
using the USB port on the battery adapter. Refer to the
specifications on this in "Technical Data".
socket 11 on the battery adapter 2.
The connected USB device will be charged.
English | 11
1 609 92A 3BL | (22.9.16)