Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
prescribed speed of the machine. The machine speed is indicated on a decal on the gearbox-cover.
9.
Before you engage the tractor P.T.O. you must check if nobody, also children and animals, is nearby the machine.
10. Never engage the tractor P.T.O. when the tractor motor is shut-off.
11. Disengage the tractor P.T.O. when the angle of the P.T.O. shaft becomes to big.
12. Be aware that the machine will still run for a while after you have disengaged the tractor P.T.O. Do not come close
to the machine while it is still running.
Only when the machine completely stands still, it is allowed to start adjustment-, cleaning-, service- and/or repair-
work.
13. Adjustment, cleaning-, service- and / or repair-work are only allowed to be done when the tractor P.T.O. shaft is
disengaged, the motor shut-off and the tractor key is pulled out.
14. The disconnected P.T.O. shaft must by 'stored" by the corresponding chain.
15. After you have disconnected the P.T.O. shaft you must replace the tractor P.T.O. shaft cover directly
1.2.3
Service
1.
During adjustment-, cleaning- and service-work, but also when you have to remove an object out of the machine
you must disengage the tractor P.T.O. shaft , shut-off the motor and pull the tractor key out.
2.
Check at regular times (at least every 8 hours) all bolts and nuts. Re-tight them if necessary.
3.
Use adequate supports when you have to work under a lifted machine.
4.
Use always correct tools and wear gloves when you replace flails.
5.
Collect used and excess oil and grease for environment friendly disposal.
6.
Check at regular times (at least every 8 hours) the condition of the protection elements and wear-off parts. replace
them if necessary.
7.
Disconnect the dynamo ánd the battery during electric welding-work
8.
Re-placement parts must comply at least the manufacturer specifications.
You do not have doubts when you use original PERFECT parts !!!
1.3 Technische Specifications
Cutting width
Speed flail rotor
Quantity of flails
Minimum tractor power
Maximum tractor power (without overload clutch) kW/pk
Cutting height
Coupling
Offset to the recht (from middle point of the tractor)
Machine width
Machine height
Machine depth (from pin 3-point)
Machine weight
Noise level in tractor driver area
Cutting width
Speed flail rotor
Quantity of flails
Minimum tractor power
Maximum tractor power (without overload clutch) kW/pk
Cutting height
Coupling
Offset to the recht (from middle point of the tractor)
Machine width
Machine height
Machine depth (from pin 3-point)
Machine weight
Noise level in tractor driver area
BG2/BK2
cm
omw./min.
± 2100
n – 2,2Kg (0,9Kg)
kW/pk
22 / 30
30 / 41
cm
Kat.
cm
cm
cm
cm
Kg
485 / 515
BG2/BK2
cm
omw./min.
± 2100
n – 2,2Kg (0,9Kg)
kW/pk
30 / 40
55 / 75
cm
Kat.
cm
cm
cm
cm
Kg
710 / 750
9
BG2 / BK2
– 105
– 120
105
120
± 2100
6 (12)
8 (12)
26 / 35
35 / 48
5 – 10
5 – 10
I / II
I / II
65
80
125
142
950
950
125
125
515 / 545
70 dB(A)
BG2 / BK2
– 150
– 180
150
180
± 2100
9 (16)
12 (20)
33/ 45
55 / 75
5 – 10
5 – 10
I / II
I / II
110
140
170
200
950
950
145
145
760 / 800
70 dB(A)
BG2 / BK2
– 135
135
± 2100
8 (12)
27 / 37
37 / 50
5 – 10
I / II
95
155
950
125
540 / 575
BG2 / BK2
– 210
210
± 2100
12 (20)
38 / 52
55 / 75
5 – 10
I / II
107
230
950
145
810 / 850
Publicité
Chapitres
Table des Matières
