Technical Specifications - Bort BFP-18A Mode D'emploi

English
Cordless sprayer
THE NUMBERS MENTIONED IN THE TEXT
CORRESPOND WITH THE PICTURE SAT PAGE2.
TECHNICALSPECIFICATIONS
Battery voltage / Capacity
Maximum nozzle fl ow rate
Container capacity
Weight
PRODUCT INFORMATION
1. Motor housing
2. Output control
3. Triggerswitch
4. Handle
5. Paintcontainer
6. Spray basket nozzle
7. Spare valve
8. Viscositycup
SAFETY INSTRUCTIONS
The following symbols are used in these instructions
for use:
Denotes risk of persona! injury, loss of life or
damage to the tool in case of non-obser-
vance of the instructions in this manual.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions
and how to operate it. Maintain the machine in accord-
ance with the instructions to make sure it functions
properly. Keep this manual and the enclosed documen-
tation with the machine.
ADDITIONAL SAFETY INSTRUCTIONS
- NEVERSPRAY AT PERSONS- Neveraim the nozzle
at another person or animal. Never allow the spray
to come in to direct con tact with the skin.
FLASH POINT - This spray gun must not be used for
spraying fl ammable paints and solvents with a fl ash
point of less than 32°C
VENTILATION - Always make sure that there is ad-
equate ventilation in the work area when spraying.
- BASKET NOZZLE - Always keep the spray basket
nozzle in piace during use.
- CONSIDER WORK AREA ENVIRONMENT - Do not
use spray guns where there is a risk of fi re or explo-
sion.
- BEWARE OF ANY HAZARD - Beware of any hazard
by the material being sprayed and consult the mark-
ings on the container or the information supplied by
the manufacturer.
- DO NOT SPRAY-Do not spray any material where
the hazard is notknown.
18 V / 1.2 Ah
300 ml/min
500ml
1.9 kg
A
- USE EYE PROTECTION - Always use appropriate
eye protection to keep hazardous vapours or fumes
out of the eyes.
- WEAR A MASK - Never operate a spray gun without
wearingaface mask.
- PROTECT YOUR EARS - Wear ear protectors if the
sound pressure exceeds 85 dB(A).
- MAINTAIN YOUR TOOLS - Keep your spray gun,
paint container and nozzles clean. Do not clean with
fl ammable liquids with a fl ash point less than 32°C
Inspect the mains lead periodically and if damaged
have it replaced by a qualifi ed person.
- NAKED FLAMES - Never spray near a naked fl ame
or appliance pilotfl ame.
- SMOKING - Never smoke whilst spraying. THIN-
NING - Always read the paint manufacturers thin-
ning recommendations or instructions before using
paint or other materials.
• SWITCH OFF WHEN NOT SPRAYING - Avoid run-
ning the unit with the fl ow rate knob fully closed for
any length of time.
We accept no responsibility for damage caused by
the use of unsuitable substances, or paints that hare
not been thinned correctly, and any health hazards
that arise from lack of adequate ventilation
OPERATION INSTRUCTIONS
PREPARATION B
Do not use textured wall paints or coatings as
this wHIblock the nozzle.
To obtain the best results, it is important that you pre-
pare the surface to be sprayed and thin the paint to
the correct viscosity, before you operate your spray
gun. Always ensure that the surfaces to be sprayed
are free from dust, dirt and grease. Make sure that you
have masked the areas that should not be sprayed,
using a good quality masking tape. The paint or fl uid
to be sprayed should be thoroughly mixed and free
from lumps or other particles. Many substances can
be sprayed with your spray gun, but always check the
manufacturers recommendations before purchasingy-
our paint.
THINNING
Always remember to disconnect from the
mains sup-ply before fi lling the paint contain-
er with sprayable material.
Most paints are supplied ready for brush application
and will need to be thinned before they are suitable to
be sprayed. Follow the manufacturers advice on thin-
ning the paint when used with a spray gun. The viscos-
ity cup will help you to determine the correct viscosity of
paint to be used. To determine the correct viscosity, fi ll
the cup to the brim with the paint. Measure the amount
of time it takes for the cup to empty back into the can.
The table below shows recommended times for differ-
ent types of material.
7