Télécharger Imprimer la page

Kuppersbusch KI6880.1SR Mode D'emploi page 64

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 66
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
Warning
Keep the control panel of the
heating areas clean and dry at all
times.
In the event of operating
problems or incidents not mentioned
in this manual, disconnect the
a p p l i a n c e a n d c o n t a c t t h e
Suggestions and
recommendations
* Do not slide pots and pans over the
glass because they could scratch it.
* Although the glass can take knocks
from large pots and pans without
* To avoid damaging the ceramic
pans over the glass and keep the
undersides of them clean and in good
condition.
* Recommended diameters of the pot
bottom (see ''Technical Data Sheet''
supplied with the product).
Try not to spill sugar or products
containing sugar on the glass as
while the surface is hot these could
damage it.
Cleaning and maintenance
clean it using suitable products and
implements once it has cooled down.
This will make the job easier and avoid
the build-up of dirt. Never use harsh
cleaning products or tools that could
equipment.
Light dirt not stuck to the surface can
be cleaned using a damp cloth and a
gentle detergent or warm soapy water.
use a special cleaner for ceramic hot
plates and follow the instructions on
to being burned repeatedly can be
removed using a scraper with a blade.
Slight tinges of colour are caused by
pots and pans with dry grease residue
underneath or due to grease between
the glass and the pot during cooking.
These can be removed using a nickel
scourer with water or a special cleaner
sugar or food containing a lot of sugar
that have melted onto the surface
must be removed immediately using
a scraper.
Metallic sheens are caused by dragging
metal pots and pans over the glass.
These can be removed by cleaning
thoroughly using a special cleaner
you may need to repeat the cleaning
process several times.
Warning:
A pot or pan may become stuck
to the glass due to a product having
melted between them. Do not try to
lift the pot while the heating zone is
cold! This could break the glass.
Do not step on the glass or lean
on it as it could break and cause
injury. Do not use the glass as a
surface for placing objects.
reserves the right to
make changes to its manuals that it
affecting the product's essential
features.
Environmental
considerations
The symbol
on the product
or its packaging means that this
product cannot be treated like
ordinary household waste. This
product must be taken to a recycling
collection point for electrical and
that this product is disposed of
correctly, you will avoid harming
the environment and public health,
which could happen if this product
is not handled properly. For more
detailed information about recycling
this product, please contact your
local authority, household waste
service or the store where you
purchased the product.
The packaging materials used are
environmentally friendly and can
be recycled completely. Plastic
components are marked >PE<, >LD<,
EPS<, etc. Dispose of packaging
materials, like household waste, in
your local container.
F u l f i l l m e n t
w i t h
Efficiency of the appliance:
-Appliance has been tested
according to standard EN 60350-2
and the obtained value, in Wh/Kg,
is available in the appliance's rating
plate.
Following advices will help you to
save energy anytime you cook:
* Use the correct lid for each pot
whenever is possible. Cooking
without lid uses more energy.
* Use pans with flat bases and
appropriate base diameters in order
to match size of the cooking zone.
Pan manufacturers usually provide
top diameter of the pot that is always
larger than base diameter.
little quantities in order to preserve
vitamins and minerals of vegetables
and set the minimum power level
that allows maintaining the cooking.
High power level is unnecessary and
a waste of energy.
* Use small pots with small quantities
of food.
If something does not work
perform the verifications described
below.
The appliance does not work:
Ensure that the power cable is plugged
in.
The induction zones do not produce
heat:
The container is not appropriate (it does
not have a ferromagnetic bottom or is
too small). Check that the bottom of the
EN
E n e r g y
63

Publicité

loading

Ce manuel est également adapté pour:

Ki8880.1srKi9880.1sr