Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
H-2560
HEX PICNIC TABLE
TOOLS NEEDED
Power Drill
Level
Tabletop x 1
IMPORTANT! Do not fully tighten screws until
end of assembly.
IMPORTANT! Verify all parts are present before
beginning assembly.
1.
Loosely attach one anchor block to bottom of each
seat using two 3½" hex lag screws, two washers and
power drill with 7/16" socket bit. (See Figure 1)
NOTE: The hole in the anchor block should face
the seat side with three edges.
Figure 1
3½" Hex Lag Screw
Anchor Block
PAGE 1 OF 9
1-800-295-5510
uline.com
Two Person Assembly
Recommended
7/16" Socket Bit
Phillips Head
Drill Bit
3" Deck Screw
3½" Hex Lag
x 9
Screw x 30
Base x 3
ASSEMBLY
Washer
Hole
Tape
Measure
PARTS
2½" Hex Lag
Screw x 6
Left Seat x 3
2. Place support arms on a flat, level surface. Loosely
attach using two 3" deck screws per side.
(See Figures 2a-2c)
Figure 2a
Figure 2c
3" Deck Screw
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
Washer
Anchor Block
x 36
x 6
Support Arm x 3
Right Seat x 3
Figure 2b
0623 IH-2560
Publicité
Manuels Connexes pour Uline HEX H-2560
Sommaire des Matières pour Uline HEX H-2560
- Page 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-2560 1-800-295-5510 uline.com HEX PICNIC TABLE TOOLS NEEDED Two Person Assembly Recommended Power Drill Level 7/16" Socket Bit Phillips Head Tape Drill Bit Measure PARTS Washer 3" Deck Screw 3½"...
- Page 2 ASSEMBLY CONTINUED 3. Loosely attach seats to support arms through 5. Rotate the base center support beam 90 degrees. pre-drilled holes using 12 3½" hex lag screws, Align pre-drilled hole in base and secure using 3" washers and power drill with 7/16" socket bit. deck screw.
- Page 3 11. Make sure table is level and tighten all screws. 3½" hex lag screws and washers. (See Figure 8) NOTE: H-2565 mounting hardware sold separately. Figure 8 3½" Hex Lag Screw Tabletop Washer Vertical Support 1-800-295-5510 uline.com PAGE 3 OF 9 0623 IH-2560...
- Page 4 H-2560 800-295-5510 uline.mx MESA HEXAGONAL PARA PÍCNIC HERRAMIENTAS NECESARIAS Se Recomienda Armar Entre Dos Personas Cinta de Taladro Eléctrico Nivel Dado de 7/16" Broca de Cruz Medir PARTES 9 Tornillos para 30 Tornillos Tirafondo 6 Tornillos Tirafondo 6 Bloques de Rondanas Hexagonales de 2½"...
- Page 5 CONTINUACIÓN DEL ENSAMBLE 3. Fije los asientos sin apretar a los brazos de soporte 5. Gire 90 grados el travesaño del soporte central de a través de los orificios preperforados usando 12 la base. Alinee el orificio preperforado de la base tornillos tirafondo hexagonales de 3½", rondanas y y asegúrelo usando un tornillo para madera de 3".
- Page 6 3½" y las rondanas. (Vea Diagrama 8) NOTA: La tornillería de instalación del modelo H-2565 se vende por separado. Diagrama 8 Tornillo Tirafondo Hexagonal de 3½" Cubierta Rondana Soporte Vertical 800-295-5510 uline.mx PAGE 6 OF 9 0623 IH-2560...
- Page 7 H-2560 1-800-295-5510 uline.ca TABLE DE PIQUE-NIQUE HEXAGONALE OUTILS REQUIS Montage à deux personnes recommandé Perceuse Niveau à bulle Douille de Mèche de Ruban à électrique 7/16 po perceuse cruciforme mesurer PIÈCES Rondelle Tirefond Vis de Tirefond Bloc d'ancrage x 36...
- Page 8 MONTAGE SUITE 3. Fixez sans serrer les bancs aux bras de support à 5. Faites pivoter la barre de support centrale de la travers les trous prépercés à l'aide de 12 tirefonds base de 90 degrés. Alignez le trou prépercé dans la hexagonaux de 3 ½...
- Page 9 3 ½ po et de rondelles. (Voir Figure 8) REMARQUE : Le matériel de fixation H-2565 est Figure 8 vendu séparément. Tirefond hexagonal de 3 ½ po Surface de table Rondelle Support vertical 1-800-295-5510 uline.ca PAGE 9 OF 9 0623 IH-2560...