Genesis GLCD2038A Manuel D'utilisation page 4

Do not force the power tool.
•
which it is designed. forcing the tool could possibly damage the tool and may result in personal injury.
Use the correct power tool for the job
•
it is not designed.
Do not use tool if switch does not turn it on or off.
•
the switch is dangerous and must be repaired or replaced by an authorized service center.
Turn power tool off, and disconnect the plug
•
from the power tool before making any adjustments, changing the accessories, or storing the tools. Such
preventive safety measures reduce the risk of an accidental start up which may cause personal injury.
Store idle tool out of reach of children and other inexperienced persons
•
dangerous in the hand of untrained users.
Maintain power tools with care
•
component breaks, and any other conditions that may affect the tool's operation. A guard or any other part that
is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal
injury.
Use recommended accessories
•
manufacturer or intended for use on this type tool may cause damage to the tool or result in personal injury to
the user. Consult the operator's manual for recommended accessories.
Keep cutting tools sharp and clean
•
are less likely to bind and are easier to control.
Feed the workpiece in the correct direction and speed.
•
blade, cutter, or abrasive surface against the direction of the cutting tool's direction of rotation only. Incorrectly
feeding the workpiece in the same direction may cause the workpiece to be thrown out at high speed.
Never leave the tool running unattended, turn the power off
•
until it comes to a complete stop.
BATTERY TOOL USE AND CARE
Ensure the switch trigger is in the off position before inserting battery pack.
•
Inserting the battery pack into power tools that have the switch on invites accidents.
recharge only with the charger specified by the manufacturer.
•
suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Use battery tools only with specified battery pack
•
create a risk of injury and fire.
Avoid storing battery pack in a container with other metal objects such as
•
nails, coins, clips, keys, screws, or other small metal objects that can make
a connection from one terminal to another
battery pack is not being used. Connecting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the batter
•
If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
Battery tools do not need to be plugged into an electrical outlet
•
always in operation condition. Be aware of possible hazards when not using your battery tool or when changing
accessories. following this rule will reduce the risk of electric shock, fire or personal injury.
WArNING:
OTHEr AIrBOrNE PArTICLES, INCLUDING WOOD DUST, CrYSTALLINE SILICA DUST
AND ASBESTOS. Direct particles away from face and body. Always operate tool in a
well-ventilated area and provide for proper dust removal. Use dust collection system
wherever possible. Exposure to the dust may cause serious and permanent respiratory
or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid
breathing the dust, and avoid prolonged contact with the dust. Allowing dust to get into
your mouth or eyes, or lay on your skin may promote absorption of harmful material.
Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for
dust exposure, and wash exposed areas with soap and water.
4
The tool will perform the job better and safer at the feed rate for
. Check for proper alignment and binding of moving parts,
. using accessories and attachments not recommended by the
USE OF THIS TOOL CAN GENErATE AND DISBUrSE DUST Or
20V Lithium-ion Drill/Driver
Operator's Manual
. Don't force the tool or attachment to do a job for which
Any tool that cannot be controlled with
from the power source and/or battery pack
. Properly maintained cutting tools with sharp cutting edges
. use of any other battery packs may
. Always protect the battery terminals when
GLCD2038A
. It is
feed the workpiece into a
. Do not leave the tool
A charger that is
y. Avoid contact.
, therefore, they are