Les langues disponibles
  • FR

Les langues disponibles

Quick Setup Guide
ENGLISH
5
To attach the slow-motion knobs
fi rst locate the supplied hex key hidden inside the
slot in the front of your mount.
8
Slide the dovetail bar into the clamp at the top of the
mount and tighten the hand knob on the bottom of
the clamp to secure the telescope in place.
1
130AZ
Unpack your telescope and verify that all parts are
ITEM #22461
present. Your StarSense Explorer DX includes:
a telescope tube, a tripod and mount head, an
accessory bag, slow motion controls, an accessory
tray, two eyepieces, a fi nderscope, a StarSense
phone dock, StarSense Explorer app code card,
and a hex key (hidden inside the slot in the front of
the mount head).
3
Extend the legs of the tripod by loosening the three
hand knobs on each leg. Pull each leg section all
the way out and tighten the hand knobs to secure
them in place.
6
Place the slow-motion control knob over the
to your mount,
D-shaped gear shaft and push inward to make sure
it is fully seated. Use the hex key to tighten the
setscrews onto the gear shaft. Return the hex key to
its storage position in the front of the mount.
9
Remove the cap from the focuser and insert the barrel
of the 25 mmeyepiece into the focuser. Tighten the
setscrew to secure the eyepiece in place.
2
To set up the tripod, spread the legs outward until
they are fully extended and push down the center leg
brace.
4
Place the accessory tray on top of the center brace
and line up the three holes. Insert the three thumb
screws through the top of the leg brace and thread
them into the tray.
7
Turn the clamp assembly so that the locking screw is
on top of the dovetail clamp. Hold the telescope tube
next to the mount with the dovetail bar on the tube
facing the clamp on the top of the mount arm.
10
Slide the fi nderscope bracket into the dovetail slot
on the telescope tube near the focuser. The large
window on the fi nder should be facing the front of
the telescope. Secure the bracket by tightening the
setscrew on the dovetail slot.
ENGLISH | 1
Table des Matières
loading

Sommaire des Matières pour Celestron StarSense Explorer DX 130AZ

  • Page 5 130AZ Guide d'installation rapide FRANÇAIS ARTICLE #22461 Déballez votre télescope, et vérifi ez que toutes les Pour installer le trépied, écartez les pieds vers pièces sont présentes. Votre StarSense Explorer DX l’extérieur jusqu’à ce qu’ils soient complètement comprend: un tube de télescope, un trépied avec étendus et appuyez sur l’entretoise centrale.
  • Page 6 Une fois que vous avez téléchargé l’application, téléchargez l’application StarSense Explorer sur votre munissez-vous de la carte orange présente dans appareil mobile. Recherchez « Celestron StarSense la boîte de votre télescope. Lancez l’application. Explorer » dans l’Apple App Store ou Google Play.
  • Page 7: Orienter Le Télescope

    Orienter le télescope La monture StarSense Explorer DX dispose de Pour affi ner l’orientation, ou suivre des objets célestes, freins de mouvement sur chaque axe. Pour effectuer faites tourner chacune des molettes de mouvement de larges mouvements avec le télescope, tenez ralenti comme désiré.
  • Page 8: Votre Première Nuit D'observation

    Pour en savoir plus sur ce produit, visitez la page correspondante du produit sur celestron.com. AVERTISSEMENT SUR LE SOLEIL: N’essayez jamais d’observer le soleil à l’aide d’un télescope sans utiliser un fi ltre solaire adéquat. Besoin d'assistance? www.celestron.com/pages/warranty Prenez contact avec l’assistance technique de Celestron à l’adresse celestron.com/pages/technical-support 08-20 8 | FRANÇAIS...

Ce manuel est également adapté pour:

22461

Table des Matières