Télécharger Imprimer la page

Publicité

Liens rapides

MODEL
AU-A1ZB110
INPUT VOLTAGE (V)
100-240V AC
INPUT CURRENT
0.024A
OUTPUT VOLTAGE
1-10V
NUMBER OF OUTPUTS
1
MAX LOAD
25 x 1-10V Devices
AMBIENT TEMPERATURE LIMITS
-20°C~+50°C
IP RATING
IP20 (Indoor Use Only)
NUMBER OF OPERATING CYCLES
1E4
CIRCUIT DISCONNECTION
Electronic disconnection
PROTOCOL
Zigbee 3.0
Twin and Earth 0.75~1.5 mm
CONDUCTOR TYPE & SIZE
Flat x2C+E 0.75~2.5 mm
FREQUENCY BAND
2.405 - 2.483GHz
MAX OUTPUT RF POWER
12.66dBm
INSULATING MATERIALS
Polycarbonate
GLOW-WIRE TEMPERATURE
850
°C
PROTECTIVE DEVICE
100°C Recoverable temp control
• There are no restrictions of use.
• Installation must be carried out in accordance with the latest edition of the
Wiring Rules by a qualified electrician.
• Earth terminal is for Termination only.
• Hereby, Aurora Limited declares that the radio equipment type
AU-A1ZB110 is in compliance with Directive 2014/53/EU. The full text
of the EU declaration of conformity is available at the following internet
address: www.auroralighting.com/ProductDetail/AU-A1ZB110
USING THE APP TO CONNECT THE 1-10V DIMMER
TO THE HUB
1. Download the AOne App from the App Store.
2. Follow instructions on the App to send the hub into pairing mode and pair
your devices (further details below).
3. Put the dimmer into pairing mode by:
a) Connecting the dimmer to a power outlet and turning on the power, or,
b) Pressing the pairing button for 3 seconds, or,
c) Powering the dimmer off for a minimum of 2 seconds and back on again
6 times. The on periods must be between 0.5 - 1.5 seconds.
The light fixture will flash twice to indicate it has entered pairing mode.
The light fixture will flash a third time to indicate that it has successfully
paired with the hub.
The dimmer can then be controlled using the AOne App.
1
IMPORTANT INFORMATION:
• The 1-10V dimmer and light fixture driver need to be
installed on the same circuit
• Ensure all conductors are fully inserted into the terminals
• Max loading is 25 devices depending on compatibility.
• The 1-10V dimmer can only be used with 1-10V drivers
(Driver required on specific light fixtures)
• For further details, please check specific light fixture and
driver data.
(UK)
2
(Australia)
2
4
6
www.auroralighting.com
2
+ -
L
N
5
+ -
+ -
1-10V
SIGNAL
CABLE TO
NEXT LED
DRIVER
LED DRIVER
CABLE TO
DEVICE
7
Pairing
button
3
+
LN
-
NL
L
1
100-240V AC
CABLE TO
MAINS
1-10V
100-240V AC
8
Download / control through the
AOne App
Document Version: AU-A1ZB110_V1_18
N
1
+ -

Publicité

loading

Sommaire des Matières pour Aurora AU-A1ZB110

  • Page 1 • Earth terminal is for Termination only. • Hereby, Aurora Limited declares that the radio equipment type LED DRIVER AU-A1ZB110 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.auroralighting.com/ProductDetail/AU-A1ZB110...
  • Page 2 ‫ لعمالئها نظري املنتجات املتأثرة‬WEEE ‫ أي مصا ر يف للتخلص من املنتج وفق ا ً لل و ائح‬Aurora ‫منها مع الفضالت املن ز لية أو التجا ر ية األخرى. وال حتص ّ ل شر كة‬...