Switching On And Off - Gardeo GCBE5530T Traduction Des Instructions D'origine

grass.
_ When edging, guide the appliance over
the edge guide along the grass edge.
_ The appliance will automatically feed the
cutting line during use.

SWITCHING ON AND OFF

_ To switch the appliance on, press the
on/off switch.
_ To switch the appliance off, release the
on/off switch.
If the trimmer is to be used for the first time, check
that the nylon line touches or passes over the
cutting blade. The nylon line will be cut
automatically when turn on the switch to the
maximum length. If it does not reach the necessary
length, push the head of spool with your finger while
pulling the lines .
To cut long grass, take several small cuts. Never cut
wet or very damp grass. The line has to be
protected against premature wear caused by hard
obstacles; for this purpose, keep the trimmer away
from hard surfaces using the guard's edge as a
protection. A short or worn line will reduce cutting
capacity. So, to restore the line to its optimum
length, push the implement to the ground while it is
running; this way, the line will automatically be the
correct length .
CAUTION! The short or worn line cuts less
efficiently therefore, to improve its operations,
unplug the electrical supply and repeat the
operation described in the beginning of the chapter.
These make sure that everything is functioning
properly and to familiarize yourself with the grass
trimmer.
CAUTION! After switching off, the nylon line will
continue to rotate for a few more seconds.
MAINTENANCE
maintenance to the machine,
always unplug the machine.
Regular cleaning and maintenance of you grass
trimmer will ensure efficiency and prolong the
life of your machine.
After each cutting operation, take apart and
clean out the grass and soil from; the spool and
its slot, the whole trimmer and in particular the
guard.
During operation, keep the air slots clean and
free of grass.
Only use a cloth soaked with hot water and a
soft brush to clean the grass trimmer.
Do not spray or wet the appliance with water.
Do not use detergents or solvents as these
could ruin the trimmer. The parts in plastic can
easily be damaged by chemical agents.
If the line cutting blade no longer cuts or breaks,
have this replaced by contacting an authorized
service centre.
Before performing
For repairs which have not been explained in
these instructions, contact an authorized
service centre.
After use, disconnect the machine from the
mains and check for damage;
When not in use store the machine out of the
reach of children;
Inspect and maintain the trimmer regularly.
Mains powered trimmers should only be
repaired by an authorized repairer ;
User may carry out maintenance and
adjustments. Please refer to the part of
REPLACEMENT OF THE SPOOL OF NYLON
WIRE.
Use only manufacturers
replacement parts and accessories. (Line:φ
1.2 )
TROUBLE-SHOOTING
maintenance to the machine,
always unplug the machine.
If the grass trimmer vibrates: remove the spool
and clean its slot carefully removing any grass
and so forth. If vibration persists after
reassembly, replace the spool with a new one.
In the event of the problem not disappearing,
have the trimmer checked at an authorized
service center.
If the grass trimmer does not start: check all the
electrical connections; make sure the safety
circuit-breaker has not been activated; check
that no fuse has blown in your electrical system.
If after the above checks, the grass trimmer still
dose not start, have it checked at an authorized
service center.
STORAGE
Follow these recommendations for storing the grass
trimmer:
Carry out general cleaning of the grass
trimmer and its ancillary parts (see
maintenance paragraph), the prevents mould
from forming.
Store it out of the reach of children, in a stable
and safe position and in a dry place where the
temperature is not too hot or too cold.
Store the trimmer away from direct sunlight, if
possible in a dark or barely lit place.
Do not store in a nylon bag as this could
encourage the formation of damp patches.
Do not store the grass trimmer resting on the
floor. Hang it by the upper handgrip instead, so
that the guard does not touch anything. The
resting of the guard on a surface could alter its
shape and therefore its dimensions and safety
characteristics would be modified.
recommended
Before performing
18