Atco ROYALE 20E I/C Mode D'emploi page 15

All manuals and user guides at all-guides.com
EURO • Printed in England • GB • F016 L69 838 • CLUB/ROYALE • OSW 08/01
CLUB/ROYALE - Buch Seite 3 Dienstag, 7. August 2001 2:41 14
3. Add a good-quality SAE 30 API SF in small quanti-
ties at a time, allowing it to settle. Repeatedly add
oil and check the level until it reaches the dip
stick . The engine may require up to 0.6 litres of
9
oil.
4. Refit and tighten the oil filler dip stick
C D
Petrol
Petrol deteriorates over time. Engine starting
may be difficult if you use petrol kept for more
than 30 days. Always run the fuel tank dry when
storing over 30 days.
1. Remove the petrol filler cap
to the tank, leaving approximately 6 mm of tank
space for fuel expansion.
2. Replace the petrol filler cap
3. Wipe up any spilt petrol from the engine before
starting the mower.
Battery (Electric start models)
The battery is already connected. For charging see
chapter "Battery".
C D
Grassbox/bag
Attach/remove the grassbox as shown.
Height of cut adjustment
E
Club B20
Your mower has an adjustable height of cut between
2,8 – 18 mm.
The height of cut adjusted as follows:
1. Slacken bolts on both sides of the mower.
10
2. Turn the height of cut knob
quired height of cut.
3. Tighten bolts .
10
F G
Royale models
Your mower has an adjustable height of cut between
5 – 35 mm with markings spaced between as an aid
to adjustment.
Adjusting the Cutting Height
Tilt the mower back and pull plunger
the stand 12 to extend fully.
1. Carefully release the plunger
home and rest the mower on the stand
2. Slacken bolts on both sides of the mower.
13
3. Turn the height of cut knob
quired height of cut and tighten bolts
4. Tilt the mower back and pull plunger
5. Raise the mower stand and carefully release the
12
plunger .
11
Note: For all models you may need to re-adjust the
comb after changing height of cut (see "Comb Adjust-
ment" below).
15 • F016 L69 838 • TMS • 11.07.01
Comb Adjustment
Your mower has an adjustable comb fitted which can
be brought into use on the lower heights of cut.
The comb is adjusted as follows:
E
.
9
1. Slacken nuts
2. Turn screws
Note: Take care not to set the comb tines too deep.
3. While holding screw
, add unleaded petrol
5
F
1. Slacken nut
.
5
Note: Take care not to set the comb tines too deep.
2. While holding nut
Starting and Stopping
Starting from Cold
Recoil Start Models:
1. Move the engine cut-off switch
2. Move the throttle lever
3. Turn the petrol tap
4. Move the choke lever
5. Pull the recoil cord handle
to achieve the re-
8
Electric start models:
1. Move the engine cut-off switch
2. Move the throttle lever
3. Turn the petrol tap
4. Move the choke lever
5. Turn the key clockwise to start. If the engine
11 , allowing
ensuring it is fully
11
Starting from Hot
12 .
Follow "Starting from Cold" ignore steps 4 only.
If the engine does not start or will not continue to run
8 to achieve the re-
follow the "Starting from Cold" procedure with choke
.
13
lever between the "On" and "Off" postion.
11 fully.
Stopping
1. Move the throttle lever
2. Move the engine cut-off switch
English - 3
Club models
14 .
until the comb tines just touch the
15
ground.
tighten nuts
15
comb in place.
G
Royale models
16 and screws 17
just touch the ground.
tighten screws
16
comb in place.
Using Your mower
to position
19
I
20 on.
to "On".
21
handle to return slowly after each pull.
to position
19
I
on.
20
to "On".
21
doesn't start after three attempts use the recoil cord
handle and charge the battery (see maintenance
and also fault finding sections).
19
ping.
H
to lock the
14
until the comb tines
to lock the
17
I
to ON.
18
H
.
22 . Allow the recoil
I
to ON.
18
H
.
to position Stop-
I
to OFF.
18