Black & Decker STC1820D Mode D'emploi page 11

If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
Carefully clean the spool cover and housing.
u
Remove the spool and check if the lever can move freely.
u
Remove the spool and unwind the cutting line, then wind it
u
on neatly again as described above. Replace the spool as
instructed.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory opera-
tion depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
u
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly clean the cutting line and spool using a soft
u
brush or dry cloth.
Regularly use a blunt scraper to remove grass and dirt
u
from the underneath of the guard.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your BLACK+DECKER product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
BLACK+DECKER provides a facility for the collection and re-
cycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
(Original instructions)
You can check the location of your nearest authorised repair
agent by contacting your local BLACK+DECKER office at the
address indicated in this manual. Alternatively, a list of author-
ised BLACK+DECKER repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Batteries
Z
At the end of their useful life, discard batteries with
due care for our environment:
Run the battery down completely, then remove it from the
u
tool.
NiCd, NiMH and Li-Ion batteries are recyclable. Place
u
the battery(s) in a suitable packaging to ensure that the
terminals cannot be short-circuited. Take them to any
authorised repair agent or a local recycling station.
Do not short-circuit the battery terminals.
u
Do not dispose of the battery(s) in a fire as this may result
u
in a risk of personal injury or an Explosion.
Technical data
STC1815
STC1820D
H 2
V 18
Input Voltage
DC
min
No-Load Speed
6200
-1
kg
Weight 2.6
Battery BL1118
V
Voltage
18
dc
Capacity 1.0
Ah
Li-Ion
Type
Charger 905902** (typ. 1)
V
Input Voltage
100 - 240
AC
V
Output Voltage
8 - 20
DC
Current
mA
400
Hand/arm weighted vibration value according to EN 786:
= 9.0 m/s , uncertainty (K) = 1.5 m/s
2
L (sound preasure) 76 dB(A)
PA
uncertainty (K) = 1.6 dB(A)
ENGLISH
STC1820
H 2
18
5500-7400
2.6
BL1318 BL1518 BL2018 BL4018
18 18 18 18
1.3 1.5 2.0 4.0
Li-Ion Li-Ion Li-Ion Li-Ion
.
2
11