Cequent Towing Products 24756 Instructions D'installation

Chevrolet HHR, Chevrolet Cobalt SS Sedan &Coupe,
Chevrolet Cobalt SS Supercharged & Saturn Ion Redline, Saturn
Ion 3 w/2.4L Engine, Pontiac Pursuit GT Sedan & Coupe
Vehicle frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24756F or 60815F
Wrenches: 3/4"
Drill Bits: 1/2"
VEHICLE
FORWARD
VEHICLE
REARWARD
Enlarge existing rearward slot
Cobalt, Pursuit & Ion only
1
Qty.(4) 1/2"-13 X 1-1/2" Carriage Bolt
2
Qty.(4) 1/4" X 1" X 3" Block
1. Drop muffler and tailpipe by removing all rubber isolators, behind rear axle, off of hangers. There will be (2) or (3)
depending on vehicle. On Ion Redline rearward isolator hanger needs to be bent down slightly for fastener clearance.
2. Install rearward fasteners. On Cobalt; Pursuit and Ion vehicles it will be necessary to drill both rear holes. Use rearmost
slot that does not go all the way thru frame as guide to drill clearance hole for 1/2" bolts. On HHR it is necessary to
enlarge rearmost slot on passenger side only. Fishwire 1/2" carriage bolts and blocks thru access slots in bottom of
frame both sides.
3. Install forward fasteners both sides. Insert carriage bolts and blocks into access slot and drop back down thru slot
making sure block spans both sides of slot.
4. While holding muffler down slide hitch up and over muffler and into place making sure that you do not push fasteners
back up into frame. Install conical washers and hex nuts on all (4) bolts and do not tighten.
5. Before tightening bolts slide hitch over towards the passenger's side and up against trunk pan. While holding hitch
against trunk pan tighten bolts.
6. Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft.
7. Reinstall muffler isolator hangers.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body
panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety
precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.
Regulation V-5 and SAE J684.
2005 Cequent Towing Products
z
All manuals and user guides at all-guides.com
Installation Instructions
Bumper
Drawbar Kit:
fascia
3594 or 6805
Drawbar must be used in
the RISE position only.
Vehicle frame
This is the location of the slot for
the Cobalt, Pursuit & Ion, typical
both sides. See note below.
Vehicle trunk pan
Tighten all ½" fasteners with torque wrench to 75
Do Not Exceed Lower of Towing Vehicle
2000 LB Max Gross Trailer Weight
Wiring Access Location:
HHR------------SUV 3 & 4
COBALT SS- PC1 & PC2
ION-------------PC3 & PC4
PURSUIT GT-PC1 & PC2
3
Qty.(4) 1/2" Conical washer
4
Qty.(4) 1/2" Hex nut
Lb.-Ft.
Sheet 1 of 3 24756N
Part Numbers:
24756
77132
60815
Manufacturer's Rating or
200 LB Max Tongue Weight
This is the location of the slot for the
HHR, typical both sides. See note below.
Enlarge existing
rearward hole/slot
all models.
NOTE!
Hitch has (3) attachment holes/slots per
side but only (2) are used depending on
vehicle. HHR uses center hitch slot and
Cobalt, Pursuit & Ion uses forward
hitch slot. All models use rearward
hole.
12-8-05 Rev. B