Publicité
Les langues disponibles
Les langues disponibles
e n g l i s h
Phase
In order to maintain the phase relationship and frequency
balance of the loudspeaker system, both loudspeakers must
be properly connected to the power amplifier. When properly
connected, the cones of the drivers of both loudspeakers will
move in the same direction when driven by identical speakers
will move in the same signals. If the cones move in opposite
directions, the resulting out of phase signals will create a per-
ceptible power loss, particularly in the low frequencies. the
stereophonic message will also be degraded. Amplifier and
speaker manufacturers typically indicate connection pola-
rity in one of two ways: red and black or plus and minus.
In either case, always connect red or plus to red or plus and
black or minus to black or minus. Connections should be
identical for both channels. to check that the speakers are
in correct phase, switch the system to mono while music is
being played. if the amplifier does not have a phase inver-
sion switch, it will be necessary to
change over the connections on
one only of the loudspeakers. If in
correct phase, the image should
Attention
be distinctly located between the
before operating the unit,
loudspeakers with a slight loss of
be sure that the
bass and low midrange level. If the
110-120 V / 220-240V
image is confused and not cen-
-
voltage
switch of your
trally located and there is a dras-
unit is set accordingly
tic loss of bass and low midrange
with that of your local
level, recheck your connections.
power voltage.
HOmE THEATER CONNECTIONS WITH
AN ACTIVE SUBWOOFER
Subwoofer positioning
With a crossover point below or around 150 hz, the instal-
lation position of subwoofers is not limited as human ears
and brains are not able to identify the emitting point of such
low frequencies. to get the best result, it is recommended to
try different positions and choose the one giving the best res-
ponse in the low frequencies, taking into account the room
acoustics.
Hooking up the subwoofer
2 possibilities are offered to connect the subwoofer with your
system:
7
the Cinch-RCA LINE IN
when the integrated amplifier or AV
amplifier is fitted with a LFE or Subwoofer output.
8
the hIgh-LEVEL IN
and hIgh-LEVEL Out
minals using loudspeaker cables. Note that in this case the left
annd right low-frequencies are mixed by the amplifier of the
subwoofer.
Home Cinema interconnection with the Cinch
7
RCA input
use a RCA-RCA coaxial cable from the LFE / Subwoofer of
the AV-amplifier or the stereo amplifier.
Interconnections with the HIGH LEVEL IN
terminals
If the preamp section of your hi-Fi or audio-video system is
not fitted with a low level variable Cinch-RCA output (LFE or
subwoofer output), use its loudspeaker outputs and connect
them to the subwoofer hIgh LEVEL IN terminals with a pair
of loudspeaker cables.
Be careful when connecting not to cross (-) and (+) cord of
either L (left) or R (right) channel. Such a phase inversion
might damage your main amplifier.
Connections to HIGH LEVEL OUTPUTS
these outputs can be used to bring the signal to the main
loudspeaker systems.
the signal from the L (left) and R (right) to speakers plugs
is the one being brought in by the from receiver connectors.
these outputs can thus be used to bring the signal to the
main loudspeaker systems.
SPECIFICATIONS & TECHNICAL DATA
mT32
Position
ANTIGUA
bookshelf/
main speaker
stand
PAmPERO
bookshelf/
surround speaker
on wall
JERSEY
floorstanding
main speaker
SOCOA
on/under
center
screen
ALDERNEY
floorstanding
main speaker
ORION
floorstanding
active subwoofer
9
stereo ter-
8
9
Ways
Drivers complement
2
1 x tweeter DOM 37
1 x 17 cm 17tN15
2
1 x tweeter DOM37
1 x 13 cm 13t15N
2
1 x tweeter DOM 37
2 x 17 cm 17tN15
2
1 x tweeter DOM 37
2 x 13 cm 13tN15
3
1 x tweeter DOM 37
1 x 13 cm 13tN15
2 x 17 cm 17tN15
1
1 x 21 cm 21Mt3
Publicité
