Black & Decker STC5433 Mode D'emploi page 13

Press the release tabs (29) on the line spool cap (30),
u
as shown in figure R and remove the cap by pulling it
straight off.
Pull the spool (31) out of the spool cap and clear any
u
broken line or cutting debris from the spool area.
Before placing a new spool, "park" the cutting line (32)
u
in the holding slots (33).
Feed the end of each line through the two holes (34) on
u
either side of the the spool cap ( 31 ) as shown in figure S
Slide the spool back into the spool cap. Take care to
u
keep the line from becoming trapped under the spool.
Pull slack line through until it pulls out of the holding
u
slots.
Align the tabs on the spool cap with the slots in the
u
housing (figure R).
Push the cap onto the housing until it snaps securely
u
into place.
Note: Make sure that cap is fully positioned, listen for two
audible clicks to ensure both lugs are correctly located.
Power the appliance on. In a few seconds or less you'll hear
the nylon line being cut automatically to the proper length.
Caution: To avoid appliance damage, if the cutting line
protrudes beyond the trimming blade, cut it off so that it just
reaches the blade.
Note: Other replacement parts (guards, spool caps, etc.)
are available through BLACK+DECKER service centers. To
find your local service location visit www.blackanddecker.com.
Warning! The use of any accessory not recommended
by BLACK+DECKER for use with this appliance could be
hazardous.
Note: The tool has two cutting systems:
AFS: Single line autofeed for light trimming and edging.
u
HDL: Heavy Duty Dual Line cutting system for more
u
overgrown areas.
Note: The HDL spool may be used in trimming mode only.
Fitting a new piece of heavy duty cutting line (fig.
T & U)
Replacement packs of 10 heavy duty cutting lines are
available from your BLACK+DECKER dealer (cat. no. A6489).
To fit a new piece of cutting line, proceed as follows:
Unplug the tool.
u
Keep the tabs (37) depressed and remove the HDL cap
u
(16) from the housing (12).
Remove any dirt and grass from the HDL cap (16) and
u
housing.
Remove the used piece of line from the HDL cap (16).
u
Thread a new piece of line (35) through the eyelets (36) in
u
either side of the HDL cap.
Put the central ferrule (39) in the indicated position (Fig.
u
U).
Re-fit the HDL cap.
u
All manuals and user guides at all-guides.com
Rewinding spool from bulk line (use only 20mm.
round diameter line)
Do not use square, star or other shaped line or larger
diameter. These may cause feeding issues or overload the
motor.
Bulk line is also available for purchase from your local retailer.
Note: Hand wound spools from bulk line are likely to
become tangled more frequently than BLACK+DECKER
factory wound spools. For best results, factory wound spools
are recommended.
To install bulk line, follow the steps below:
u
u
u
u
u
u
u
u
u
u
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u
u
u
u
u
(Original instructions)
Remove battery from appliance.
Remove the empty spool from the appliance as
described in "Replacing the spool."
Remove any remaining cutting line from the spool.
First, wind new line in the channel of the spool closest
to the holding slots as shown in Figure V.
Place the end of the cutting line (32) into the retaining
hole (40) (Figure W).
Wind the cutting line onto the spool in the direction
of the arrow on the bottom of the spool. Make sure to
wind the line on neatly and in layers. Do not crisscross.
When the wound cutting line reaches the beginning of the
holding slots, cut the line approximately 106 mm.
Push the line in the holding slot on one side of the spool
to hold the first line while you wind the second line.
Repeat the above procedure for the second cutting line
on the lower section of the spool.
Fit the spool into the appliance as described in
"Replacing the spool".
Switch off and unplug the appliance/tool.
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
ENGLISH
13