Evermount EM-FT Mode D'emploi

THE WARRANTY WILL ONLY BE VALID IF YOU FOLLOW THE INSTRUCTIONS BELOW CAREFULLY.
• The EverMount EM-FT is designed to mount an LCD screen onto a vertical
wall. Hardware for mounting to a wood stud is included. For mounting to any other
surface, contact a qualified contractor.
• This product will hold flat screens from 26 to 45 inches and weighing up to 110 lbs. Optional tilt
plates are included for a tilt of 5°.
• You will need: a Phillips screwdriver, a ratchet or driver with 13 mm socket, an electric drill with
a 1/4" drill bit, a stud finder and a level.
• A minimum of two people are required for this installation.
• If you do not understand the instructions, or are not sure you can follow them safely,
contact a qualified contractor.
• The wall or mounting surface must be capable of supporting the combined weight of the
mount and the display; otherwise the structure must be reinforced.
INPROPER INSTALLATION MAY CAUSE SERIOUS INJURY AND/OR DAMAGE. IT IS RECOMMENDED THAT
A QUALIFIED CONTRACTOR INSTALL THE EM-F1.
Part 1– Mounting the Wall Plate (Drywall)
Important! For safety, this mount must be secured to two adjacent wood studs at least 16" apart.
1. Check to ensure you have everything on the parts list. To acquire missing parts please visit
www.everik.com/parts.html or call 1-866-604-6966.
2. Using a stud finder, locate and mark two adjacent studs for securing the mount.
3. Place the wall plate against the wall and level it.
4. Mark four locations (two per stud) on the wall where the mount will be secured. Be sure to use
the center of each stud.
5. Remove the wall plate and drill a 1/4" pilot hole at each location using an electric or portable drill.
6. With the help of another person, replace the wall plate and fix it to the wall using the Lag Bolts (Q)
and Lag Bolt Washers (R) provided.
7. Do not over-tighten the bolts and do not release the wall plate until all screws are secure.
Bag Ref Item Qty
(A) M4x12 Bolt 4
1 (B) M4x30 Bolt 4
(C) M4 Lock Washer 4
(D) M5x12 Bolt 4
2 (E) M5x30 Bolt 4
(F) M5 Lock Washer 4
(G) M6x12 Bolt 4
3
(H) M6x35 Bolt 4
(I) M6 Lock Washer 4
092008
All manuals and user guides at all-guides.com
Bag Ref Item Qty
(J) M8x16 Bolt 4
4 (K) M8x40 Bolt 4
(L) M8 Lock Washer 4
(M) Small Spacer 4
5 (N) La rge Spacer 4
(O) M6 Washer 4
(P) Concrete Anchor 6
6
(Q) Lag Bolt 6
(R) Lag Bolt Washer 6
Optional tilt plate 2
(S)
7
(T) M5x35 Bolt 4
(U) M5 Nut 4
Part 2 – Attaching the Arms to the Display
Important! Use extra care during this part of the installation. Avoid laying your display face down if
possible as it may damage the viewing surface
1. Examine the back of your television. If the back of your display is flat, you will be using one
of the shorter bolts from the hardware kit. If the back of your display is curved or recessed, you
will be using one of the longer bolts and a spacer.
2. Determine the correct diameter bolt to use by trying one bolt each from Bags 1 - 4 of the hard-
ware kit. Do not force any of the bolts – if you feel resistance stop immediately to avoid
damaging your display.
3. Attach the arms to the back of your display using the bolts identified in Steps 1 and 2 and the
corresponding Lock Washer (C, F, I, or L).You will need to use the M6 Washers (O) if you are using
the M4, M5, or M6 bolts. If your display has a curved or recessed back, you may also need to use a
Spacer (M or N).
4. Make sure the screws are snug, but do not over-tighten.
Part 3 – Final Installation and Adjustment
1. With the help of another person, carefully lift your display and place it on the wall plate.
install optional tilt plates as shown in the diagram.
2. Insert the safety bar at the bottom of the mount to prevent it from being accidentally
knocked off the mount. A padlock can be used to help protect your display from theft.
Optional tilt plates (S)
Wall plate
T
U
Arms
EM-FT
If desired,
Safety bar
Made in China
Imported by Everik International Inc.