Publicité
Les langues disponibles
Les langues disponibles
Indicator lights
-
The cooling function is indicated by the green indicator light. The red indicator light indicates that the
keep warm function is on.
OFF
COLD
HOT
Caution
-
The product is not designed to cool hot food or quickly reheat cold food. The product is designed to
keep cold or hot food at the same temperature as it is transferred. It may take a long time to cool hot
food or reheat cold food.
-
If the product needs to be switched into cooling and heating functions during operation, the function
switch should be set to the "OFF" position and switched after 30 minutes, otherwise the life of the
product will be shortened.
-
This product is suitable for cold storage of packaged foods and beverages such as fruits, vegetables
and soft drinks. Fresh food should not be kept for a long time. Do not add carbonated beverages when
heating to prevent cracking.
-
Follow the following instructions to prevent food contamination:
-
Opening the door (lid) for a long period of time can cause a significant increase in the temperature of
the cooling compartment;
-
Regularly clean surfaces that may come in contact with food and accessible drainage systems;
-
If the product is empty for a long time, close the lid, defrost, clean, dry and keep it open to prevent
mold in the refrigerator.
Energy-saving advice
-
Place the product in a dry and well-ventilated place so that the product is not near a heat source and is
not exposed to direct sunlight.
-
High-temperature foods should be cooled to room temperature and refrigerated.
-
Keep the lid of the product closed as much as possible.
Maintenance and Cleaning
-
Disconnect the power supply before each cleaning, maintenance and after each use.
-
When cleaning, make sure that no water enters the live part.
-
Clean with a soft towel, lukewarm water or an undiluted detergent.
-
Clean the door rubbers with a damp, clean cloth and dry thoroughly.
-
Do not use abrasive or harsh cleaning agents.
-
Do not rinse the product with water.
Storage
-
Store the product in a dry, clean place. Do not store the product in extremely high or low temperatures.
The recommended storage temperature is 25˚C with humidity ≥ 75%.
If the product is not going to be used for an extended period of time, follow these instructions:
1.
Turn off the product.
2.
Remove all parts inside the product.
3.
Dry all moisture inside the product with a clean cloth.
4.
Store the product in a dry, clean place.
5.
Leave the lid slightly open to prevent unpleasant odors and mold.
16
Troubleshooting
Problem
The indicator light does not
- The plug is not properly
come on and the fan is not
plugged in.
running.
- The switch is not turned on.
The fan is working, but the
The indicator light is broken.
indicator light is not on.
The indicator light is on, the
- The cooling plate is broken.
fan is working but the pro-
- The heatsink wire has come
duct is not cooling/heating.
The color of the indicator
- There is an incorrect polarity
light does not match the po-
of the DC power supply.
sition of the function switch.
The indicator light is on, the
- The cooling plate is broken.
fan is working but the pro-
- The heatsink wire has come
duct is not cooling/heating.
- The ventilation grille is bloc-
The indicator light is on,
the fan is working but the
- There are too many objects in
product does not cool/heat
the product.
properly.
- The lid is not closed properly.
Disposal - Recycle
-
Contribute to a cleaner living environment! This product is subject to the European Directive (EU)
2012/19/EU. Do not dispose of the product with the household waste. For proper recycling, please
contact your local authority or your household waste disposal service for further details on your nearest
designated collection point.
Cause
Solution
- Plug into an electrical outlet.
- Check for power failure.
- Check that the switch position is
correct.
- Check if the cigarette lighter fuses (in
the car) are damaged.
Engage authorized personnel to
replace the bulb.
Engage authorized personnel to check
if the cooling plate wire has fallen off
off.
or to replace the cooling plate.
- Check that the polarity of the DC
power supply matches the power
demand of the product.
- Engage authorized personnel to
check if the cooling plate wire has fal-
off.
len off or to replace the cooling plate.
- Remove dust and objects near the
ked.
ventilation grid.
- Too many items in the product requi-
re longer cooling time.
- Check that the lid is closed.
17
Publicité
