Publicité
Les langues disponibles
Les langues disponibles
Commando Shelter Instructions
Tools Required: Phillips Screwdriver, 7/16" deep well socket, 7/16" wrench. A cordless drill is recommended.
TENT ASSEMBLY
1.
Lay tent [G] under back edge of base [H], (opposite side from corner brackets) with the yellow Velcro straps facing up. (Fig. II).
2.
Starting with the U-frame [I] closest to the base, and the Velcro closest to the base; wrap the yellow Velcro straps around
the U-frame [I]. (Fig. II) Note: Yellow Velcro straps should be on inside of tent after assembly.
3.
Repeat step 2 for 3 more U-frames [I].
4.
Fasten the corner velcro pieces to U-Frame. (Note: This U-frame pole touches the ground when in closed position.) Attach Velcro straps.
(CAUTION! In a small amount of incidences, sharp edges of the screws may protrude thru the lip of the base after
assembling the Storm Guard System. Please use caution when loading and unloading unit.)
1.
Flip unit to the closed position.
2.
Take the storm guard system attachment [S] and find the middle.
3.
From the center of the back of the base [H] pull the tent [G] tight so the front U-frame [I] is just touching the
ground.
4.
Wrap the excess tent material under the lip on the base [H] and push the storm guard system attachment
[S] over the top of the tent material and onto the lip on the base [H] across the back edge. (Fig. IV) Before
continuing to the sides, insert 3 #8 Phillips head screws [T] across the back evenly. The Philips head screws
[T] should go through the storm guard attachment [S], tent [G], base [H], and back into the storm guard
attachment [M]. (Fig. VI)
5.
Continue pushing the storm guard system attachment [S] over the tent material onto the lip to either side
making sure the tent is tight.
6.
Take the remaining Philips head screws [T] and starting at one end of the storm guard system attachment
[S] insert the Philips head screws [T] at least every 8 inches on each side of the base [H]. NOTE: may have extra
screws when finished.
7.
At the front of the base locate the 2 holes. Thread the yellow rope [U] toward the inside of the base [H].
Secure each end with a knot.
8.
Step inside the base [H] and attach Velcro windows [AA].
9.
The seat (F) can now be installed onto the front seat assembly (P) and the back seat assembly (N). Insert the
safety pin (Q).
Set Up
Move to the front side and lift U-Frames toward you to enclose the base area.
Note: Don't force movement. If shelter binds, check for catch points.
Tent Positions
Collapsed – Tent down resting on the base for transport or storage
Closed – Tent rotated over the base onto the ice.
Windbreak – First pole raised with windbreak bar rotated over front U-Frame pole.
Collapsed
Collapsing for Transport
1. Fully rotate the frame to the collapsed position.
2. Make sure all the material is tucked into the base to eliminate dragging the tent material.
3. Place bucket, tackle and poles inside base.
Frabill Instruction Manual For Commando Shelter • Manuel d'instructions pour abris sur glace Commando
Closed
Windbreak
Approximate Assembly Time: 1 Hour
U
Fig. II
Back U-Frame
Front U-Frame Pole
Fig. IV
L
Start attaching storm guard
from middle of base
Y
S (front)
T (back)
Seat in Storage Position
1-800-558-1005 • service@frabill.com • www.frabill.com
Fig. I
T
S
Fig. III
3 4
2
1
Fig. V
Fig. VI
Publicité
