Makita DVP180 Manuel D'instructions page 6

Cordless vacuum pump safety
warnings
Read carefully instructions in the literature, strict
observance of procedures is main condition for operator
safety.
The vacuum pump is a machine used to
1.
evacuate refrigeration and air conditioning
equipment and recovery vessels. Do not use
it for other applications. Doing so may result in
accidents.
2. Always inspect the vacuum pump for oil leaks
before use. Failure to do so may result in fire.
3. Check the oil level and condition (deterioration,
etc.) to enable safe and efficient work.
Wear safety glasses and gloves when handling
4.
refrigerant; avoid contact with refrigerant,
blindness and injuries may result to operator.
5. Adequate performance may not be obtained in
extremely hot or cold environments.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1. Before using battery
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2. Do not disassemble battery cartridge.
If operating time has become excessively
3.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to water or
(3)
rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
All manuals and user guides at all-guides.com
cartridge, read all
6 ENGLISH
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. Follow your local regulations relating to
disposal of battery.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will also
void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery
3.
temperature at 10°C - 40°C (50°F - 104°F). Let a
hot battery cartridge cool down before charging
it.
4. Charge the battery cartridge if you do not use it
for a long period (more than six months).
PARTS DESCRIPTION
► Fig.1:
1. Sight glass
2. Oil fill/Exhaust cap
3. Intake shut-off valve
4. Handle
5. Battery holder
6. Battery
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the pump is
switched off and the battery cartridge is removed
before adjusting or checking function on the pump.
Installing or removing battery
cartridge
CAUTION:
Always switch off the pump before
installing or removing of the battery cartridge.
CAUTION:
Hold the pump and the battery
cartridge firmly when installing or removing battery
cartridge. Failure to hold the pump and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the pump and battery cartridge
and a personal injury.
cartridge with room
7. Power switch
8. LED lamp
9. Motor
10. Base
11. Oil tank
12. Drain plug