Publicité
8. Het tafelblad opbergen.
Op de knop drukken om de voet (r) los te klikken en deze uit zijn inkeping te verwijderen
Daarna het tafelblad verwijderen en de voet hieronder vastklikken.
Het tafelblad achter de rugleuning van de verhoger plaatsen. Het ronde gedeelte van het
tafelblad aan de bovenkant van de rugleuning vastklikken en de onderste rand in de
hiervoor bedoelde gleuven rechtstreeks op de rugleuning schuiven.
9. De verhoger opbergen.
Tegen de veiligheidsclip duwen, de rugleuning naar boven trekken en deze naar voren
klappen. De armleuningen inklappen. Het tafelblad hierboven plaatsen en dit met het
bevestigingsriempje vastmaken aan het zitvlak van de stoel.
10. U kunt de verhoger vervoeren met behulp van het bevestigingsriempje op de
rugleuning van de stoel.
GEBRUIK ALS BANKJE
11. Alle riemen, en de gordel kunnen verwijderd worden. Wanneer ze verwijderd zijn, kan de
verhoger gebruikt worden als bankje voor in de slaapkamer of de salon.
WAARSCHUWING: Wanneer u de riemen verwijderd heeft, maar u wilt ze
weer bevestigen om het bankje weer als verhoger te gebruiken, moet u
ze zorgvuldig weer bevestigen. Voordat u uw kindje weer installeert moet u controleren of de
riemen weer goed vastzitten.
REINIGING EN ONDERHOUD
• De verhoger reinigen met zeep, en een zacht doekje of spons.
• Geen ruwe spons, schuur- of reinigingsmiddelen gebruiken, om krassen te voorkomen.
• Kussens machinewasbaar op 30°, licht centrifugeren.
• Niet in water onderdompelen.
• Niet aan licht blootstellen.
• Regelmatig de veiligheidspunten, en de goede werking van de verhoger controleren.
PRECAUTIONS FOR USE
EN
WARNING!
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
• Never leave the child unattended.
• Always use the restraint system and ensure it is correctly fitted.
• Always use the chair attachment system and ensure it is correctly fitted before use.
• Always check the security and the stability of the product on the adult chair before use.
• This product is intended for children who can sit up on their own (minimu 6 months), up to the
age of 36 months or a maximum weight of 15 kg.
• Do not use this product on stools or benches.
• Ensure the booster seat is positioned in such a way as to prevent the child from pushing his
feet against the table or any other structure, as the chair to which the booster seat is attached
could tip.
• Never use the booster seat if any element is broken, twisted or missing.
• Use only Badabulle accessories and spare parts.
• For use only with children able to sit alone
• Ensure the floor and seat bottom are flat before installing the booster seat.
• Never adjust the booster seat height with the child sitting in the booster.
WARNING: For use on chairs with seat area greater than 40 x 36 cm, and with a seat back
at least 42 cm high.
DIAGRAM OF BOOSTER SEAT SPARE PARTS
a. Left handle / left armrest
b. Location of left handle
c. Right handle / right armrest
d. Location of right handle
e. Handle safety clip
f. Seat back cushion
g. Seat cushion
h. Booster safety clip
i. Chair seat attachment strap
j. Chair back attachment strap
k. Three-point harness
l. Front leg
m. Back leg
n. Front leg adjustment buttons
o. Back leg adjustment buttons
p. Tray
q. Tray pins
r. Tray leg
BOOSTER SEAT HARNESS
IMPORTANT! KEEP FOR FUTURE REFERENCE.
• Your booster seat's harness looks like this.
• Installing the safety harness on the booster seat.
WARNING: the harness must be installed on the booster seat prior to use.
1. DISMANTLING THE SAFETY HARNESS AND ATTACHMENT STRAPS
a. Press on the circle in the central buckle to unclip each end of the harness.
This will give you three separate straps.
b. Run the plastic buckle through each strap to remove it.
c. You get:
- three straps (X) with their sewn loop
- three loops (Y)
- two buckles connected to the straps on the back of the booster seat (Z1)
- one central buckle connected to the strap on the seat of the booster (Z2)
d. Thread the plastic buckle through each strap to remove it.
2. ASSEMBLING THE TWO STRAPS (X) CONNECTED TO THE SEAT BACK
a. Pass the first strap (X) from the back of the seat back through the slot.
b. After inserting the strap, slip the loop (Y) onto the strap.
c. After slipping the loop onto the strap, pass the strap through the central notch in the centre
of the buckle (Z1).
d. Run the strap through the second notch in the buckle (Z1).
e. Last, slip the strap back through the loop (Y) to block it.
f. Install the second seat back strap in the same way.
WARNING: The plastic buckles (Z1) must be positioned as in the photo in order to clip around the
central buckle (Z2).
3. ASSEMBLING THE STRAP CONNECTED TO THE SEAT
a. Pass the strap (X) through the notch under the front of the seat.
b. Slide the loop (Y) onto the strap (X).
c. Slide the strap from the back of the central buckle (Z2) as shown.
d. Slide the rest of the strap through the loop, to block it.
4. ASSEMBLING THE ATTACHMENT STRAP ON THE SEAT BACKREST
a. Thread either one of the straps (s) through the slot on the back of the booster seat.
b. Once the strap is inserted, thread the loop (u) onto the strap.
c. Once the loop is threaded, slip the strap into the central notch of the buckle (t).
d. Slip the strap into the second notch of the buckle (t).
e. Finally, thread the strap back into the loop (u) to block the strap.
5. ASSEMBLING THE ATTACHMENT STRAP ON THE CHAIR SEAT
a. Thread the second strap (s) through the slot on the lower part of the booster seat
b. Once the strap is inserted, thread the loop (u) onto the strap.
c. Once the loop is threaded, slip the strap into the central notch of the buckle (t).
d. Slip the strap into the second notch of the buckle (t).
e. Finally, thread the strap back into the loop (u) to block the strap.
BOOSTER FUNCTION
1. Installing the armrests
There are symbols on the armrests to help you differentiate them: 'L' for the left and 'R' for the
right. The armrests must be installed with the backrest lowered. Clip the left armrest (a) into
the slot (b), and the right armrest (c) into its slot (d). Ensure they are clipped in vertically.
2. Open the booster seat
Raise the booster seat back, and slot it onto the safety clips on the handles (e) and the booster
safety clip (h). Ensure the seat back is slotted into all three safety clips.
3. Remove the protective film from the back of the Velcro on the cushion (g).
Then adhere the cushion to the seat.
4. Adjusting the legs
This booster seat's front and rear legs can be adjusted independently to three heights. This
means that this booster can be adapted to any type of chair.
For example : if the chair's seat and back are fabric and rounded, you can adjust the back leg
lower than the front, so that the booster adapts to the seat back. The front and back legs can
also be adjusted to the same height. To adjust the height of each leg, press the adjustment
buttons (n or o) and pull the leg (l or m) towards you.
5. Installing the booster seat on the chair
Attach strap (i) around the chair seat, and strap (j) around the chair back. Attention: once you
have installed the booster, ensure that all straps are tight. Never use the booster without
attaching the safety straps.
6. Sitting your child in the booster
Sit your child in the booster and securely fasten the three-point harness.
9
Publicité
