LG WD200C Serie Manuel De L'utilisateur page 8

INSTALLATION INSTRUCTIONS
8
INSTALLATION INSTRUCTIONS
CHOOSE THE PROPER LOCATION
WARNING
y Two or more people are required when moving, unpacking, and
stacking the washer. Failure to follow this warning may result in
damage to property or serious bodily harm.
y Store and install the washer where it will not be exposed to
weather or to temperatures below freezing. Failure to follow this
warning can cause serious injury, fire, electric shock, or death.
y Properly ground the washer to conform with all electric govern-
ing codes and ordinances. Failure to follow this warning can cause
serious injury, fire, electric shock, or death.
y To reduce the risk of electric shock, do not install the washer in
humid spaces. Failure to follow this warning can cause serious
injury, fire, electric shock, or death.
y To ensure proper air flow, do not block the large opening on the
bottom of the washer with carpeting or other materials.
y Do not remove the ground prong. Do not use a 2-prong adapter
or 2-wire extension cord. Failure to follow these warnings can
cause serious injury, fire, electric shock, or death.
y Certain internal parts are intentionally not grounded and may
present a risk of electric shock only during servicing. Service
personnel-do not contact the following parts while the appliance
is energized. : pump, motor, noise filter cover, and heater (on ap-
plicable models).
CAUTION
y This pedestal washer must be installed underneath a matching
front-loading LG washing machine manufactured after 2009. (The
29" wide machine must be stacked under a 29" wide LG front-
loading washer. The 27" wide machine must be stacked under a
27" wide LG front-loading washer.)
y The pedestal washer will not work as a standalone unit.
y The pedestal washer must be stacked under an LG brand appli-
ance in order to operate properly.
POWER OUTLET
y The power outlet must be within 60 in. (1.5 m) of
either side of the washer.
y The appliance and outlet must be positioned so
that the plug is easily accessible.
WARNING
y For best performance, plug the washer into its own individual
outlet. If necessary, use a new, UL-listed 3-prong adapter or
3-wire extension cord with a 3-prong (grounding) plug rated at no
less than the branch circuit. Do not use an extension cord longer
than three feet. Failure to follow these warnings can result in
serious injury, fire, electric shock, or death
y The outlet must be grounded in accordance with current wiring
electric codes and regulations.
y Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation
of the product owner to have a proper outlet installed
by a qualified service technician.
FLOORING
y To minimize noise and vibration, the washer MUST be
installed on a solidly constructed floor.
y Allowable slope under the entire washer is a maximum 1
inch. difference from side to side or from front to back.
y Installing on carpeting and soft tile surfaces is not
recommended.
y Never install the washer on a platform or weakly supported
structure.
NOTE: The washer must be installed on firm flooring to minimize
vibration during the spin cycle. Concrete flooring is best, but a
wood floor is sufficient, provided it is built to FHA standards. The
washer should not be installed on rugs or exposed to weather.
Do not use a drip pan as it can block the drawer. Using the drip
pan may result in increased vibration and noise during operation.
1"
27" (68.9 cm)
(2.5 cm)
29" (73.7 cm)
To ensure sufficient clearance for water lines and airflow, allow
minimum clearances of at least 1 in. (2.5 cm) at the sides and
4 in. (10 cm) behind the unit. Be sure to allow for wall, door, or
floor moldings that may increase the required clearances.
29
1
50 / " (128.3 cm)
2
3
52 / " (134 cm)
4
(20 in. [50.8 cm] additional
needed for service)
5
52 " (132.9 cm)
/
16
1
54 / " (137.8 cm)
4
1"
(2.5 cm)
3
/ " (75.6 cm)
4
32" (82.1 cm)