Publicité
Les langues disponibles
Les langues disponibles
EN
c)
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d)
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e)
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is unavoidable, use a RESIDUAL CURRENT DEVICE (RCD) protected supply. Use of an RCD reduces
f)
the risk of electric shock.
NOTE: The term "RESIDUAL CURRENT DEVICE (RCD)" may be replaced by the term "ground fault circuit interrupter (GFCI)"or "earth leakage circuit
breaker (ELCB)".
g)
It is recommendation that the tool always be supplied via a residual current device with a rated residual current of 30mA or less.
3) Personal Safety
a)
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing
b)
protection used for appropriate conditions will reduce personal injuries.
c)
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or BATTERY pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
d)
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
e)
Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can
f)
be caught in moving parts.
g)
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h)
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
4) Power tool use and care
a)
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which
it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be
b)
repaired.
c)
Disconnect the plug from the power source and/or remove the BATTERY pack, if detachable, from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d)
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may
e)
affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f )
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g)
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and
h)
control of the tool in unexpected situations.
i)
Operating a tool that is not completely of fully assembled could result in injury or property damage. Do not operate this tool until it is completely
assembled. Keep all fasteners tight. Keep adjustments per tool's specifications
5) Service
a)
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is
maintained.
b)
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Safety Warnings for Sanding Operations
1.
This power tool is intended to function as a sander. Read all safety warnings, instructions and specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire, or personal injury.
2.
Operations such as grinding, wire brushing, polishing or cutting-off, are not recommended to be performed with this power tool. Operations for which the tool
was not designed may create a hazard and cause personal injury.
3.
Do not convert this power tool to operate in a way which is not specifically designed and specified by the tool manufacturer. Such a conversion may result in
a loss of control and cause serious personal injury.
4.
Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your
power tool, it does not assure safe operation.
5.
The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed
can break and fly apart.
6.
The outside diameter and thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be
adequately guard or controlled.
7.
Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheel for chips or cracks, backing pad for cracks, tear or excess
4
Publicité
