Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION INSTRUCTIONS (CONT.)
STEP 2: INSTALLING THE LAUNDRY FAUCET
Fig. 5
Assembled
Spout & Spray
Deck Plate
SINK
Rubber
Washer
Metal
Washer
C-shiped Clip
with Screws
TEHILALAUNDRY.COM | support@tehilalaundry.com
We reserve the right to make revisions in the design and informa�on without no�ce | Image is for reference only, styles varies by models
SKU Numbers: 040JS6510BLKBLK, 040JS6510BLKSS, 040JS6510WTBLK, 040JS6510WTSS, 040JS6510GRYBLK, 040JS6510GRYSS, 040JS6510BLBLK, 040JS6510BLSS,
040US6510BLKBLK, 040US6510BLKSS, 040US6510WTBLK, 040US6510WTSS, 040US6510GRYBLK, 040US6510GRYSS, 040US6510BLBLK, 040US6510BLSS
1. Take the faucet out of the box.
2. A�ach DECK PLATE to faucet.
3. Posi�on faucet on sink.
4. From underside of sink, assemble RUBBER
WASHER, METAL WASHER, and C-SHAPED
CLIP WITH SCREWS. Tighten the locknut by
hand and secure the screws with screwdriver
(see Fig. 5).
5. Fix the WEIGHT to the WEIGHT LINE and align
it with the MARKED LABEL (see Fig. 6).
6. Connect the SPRAY LINE to WEIGHT LINE
(see Fig. 6).
7. DO NOT CONNECT THE HOT & COLD SUPPLY
LINES YET. SEE STEP 4 FOR CONNECTING
SUPPLY LINES.
Fig. 6
Spray Line
Connect the
spray line to
Marked
the weight line
Label
(pull-down line)
Weight
Weight Line
STEP 3: INSTALLING THE PLASTIC DRAINAGE
NOTE: When installing new plas�c drainage, loosely �ghten all pieces first to make sure
of proper fit, then make final connec�ons.
Fig. 7
Start
here
Sink Strainer
STEP BY STEP (see Fig. 7):
1. Slide Slip Nut
threads up onto the Tail-Piece
Flanged Washer
in top of Flanged Tail-Piece
2. Tighten the top Tail-Piece
to the Sink Strainer with Slip Nut
3. Insert Slip Nut
threads down and Washer
Tail-Piece
.
4. Insert Slip Nut
threads down onto Wall Tube
Nut and Washer (not provided) onto other end of Wall Tube
5. Place flanged end of Wall Tube
into lower por�on of J-Bend
and �ghten with Slip Nut
. If wall connec�on is standard 1 ½ in.
threaded pipe, install wall tube directly into pipe and �ghten Slip
Nut and Washer (not provided).
NOTE: If wall connec�on is to 1 ½ in. plas�c pipe, a Conversion
Adapter, purchased separately, will be required for proper
installa�on (see Fig. 8).
6. Swing J-Bend
to align with bo�om of flanged Tail-Piece
Connect J-Bend
to Tail-Piece
and �ghten it with Slip Nut
tail-piece is too long, a hacksaw or tubing cu�er may be used to
trim away excess material.
x 3
x 2
Not included
in the package
, and insert
Fig. 8
.
Conversion
.
Adapter
in bo�om end of the
, then insert Slip
.
.
. If
ID: 11740
Rev. 06/14/2021
PG. 2
Publicité
