TEHILA 040JS6510BLKBLK Mode D'emploi

INSTALLATION INSTRUCTIONS
ATTENTION
1. PRIOR TO INSTALLATION: Check all parts carefully to ensure no damage occurred in transit
and no pieces are missing. DO NOT dispose of any packaging un�l you are sa�sfied with this
product.
2. SAFETY PRECAUTIONS: Your installa�on must comply with all local plumbing codes. Have a
qualified tradesman install or approve your plumbing installa�on. Always wear safety goggles
and gloves during installa�on to avoid personal injury.
3. NEED HELP? Please call us at 1 (773) 265-2371 or contact us via email at
support@tehilalaundry.com with any ques�ons. Our normal business hours are Monday to
Friday from 8 a.m. to 5 p.m. CST.
DO NOT RETURN THE UNIT TO THE PLACE OF PURCHASE BEFORE CONTACTING
US AT 1 (773) 265-2371 OR VIA EMAIL AT SUPPORT@TEHILALAUNDRY.COM.
CARE AND MAINTENANCE
FOR LAUNDRY TUB:
1. Only soap or qualified non-abrasive surface cleaner and water should be used for cleaning
the thermoplas�c sink. Rinse well and dry with so� cloth to prevent scratches.
2. Clean grease, oil, paint, and ink stains with isopropyl (rubbing) alcohol. Immediately rinse
with water a�er stain removal.
3. Avoid using razor blades or other sharp instruments that may damage or scratch the surface.
FOR FAUCET:
1. Clean the area of the moun�ng holes before installing the faucet.
2. To maintain the appearance of your faucet, always blot dry any water from the faucet's
surface. Clean with a damp, non-abrasive sponge and wipe with a clean so� cloth. To
remove water spots, apply warm water with a damp so� cloth. Always rinse thoroughly a�er
using a cleaning agent.
3. Although the finish is extremely durable, it can be damaged by some cleaners. DO NOT use
detergent powder, polishing powder, granular detergent, or a nylon brush to clean.
4. DO NOT use abrasive detergents. If used, rinse thoroughly and wipe dry with a so� cloth.
5. DO NOT install in working environments less than 32 degrees F (0 degrees C).
6. Shut off the water supply valves when the faucet will not be in use for an extended period of
�me.
7. DO NOT install the faucet in a rusty or corrosive environment.
8. DO NOT TIGHTEN the faucet too hard to avoid deforma�on or fracture.
MATERIALS AND TOOLS NEEDED
Phillips Screwdriver, Flat Screwdriver, Silicone, Carpenters Level, Pliers, Pipe Wrench, Plumbers
Pu�y, Hacksaw, U�lity Knife.
INSTRUCTION: 117017
TEHILALAUNDRY.COM | support@tehilalaundry.com
We reserve the right to make revisions in the design and informa�on without no�ce | Image is for reference only, styles varies by models
SKU Numbers: 040JS6510BLKBLK, 040JS6510BLKSS, 040JS6510WTBLK, 040JS6510WTSS, 040JS6510GRYBLK, 040JS6510GRYSS, 040JS6510BLBLK, 040JS6510BLSS,
040US6510BLKBLK, 040US6510BLKSS, 040US6510WTBLK, 040US6510WTSS, 040US6510GRYBLK, 040US6510GRYSS, 040US6510BLBLK, 040US6510BLSS
WHAT'S INCLUDED IN THE BOX
Drainage
Kit
Thermoplastic Sink
STEP 1: HOW TO PUNCH OUT FAUCET HOLES &
INSTALL STEEL LEGS
Flathead
Steel
Screwdriver
Legs
Fig. 1 Fig. 2
1. Place the laundry tub on a clean surface, such as a blanket or carboard, and turn the tub upside down to allow for the
removal of the pre-formed knockouts. These will accommodate the faucet that is going to be installed. The hole plugs may
be removed by a flathead screwdriver or a small chisel and a hammer (see Fig. 1).
2. While the tub is s�ll upside down, insert the 4 steel legs into each corner socket (see Fig. 2).
3. Use a hammer and a block of wood to drive each leg into the tapered socket un�l it is secure (see Fig. 3).
CAUTION:
• DO NOT strike the leg directly with the hammer. Place the block of wood against the leg, then strike the wood with the
hammer.
• DO NOT insert the leg all the way into the tapered socket. It's okay if there is a gap between the tub and the corner of
the steel leg. Verify that each leg is locked securely in place by gently tugging the leg.
• DO NOT wiggle the leg back and forth, as this will loosen it from the tapered socket.
4. Mount leveler to each leg. Note that there are two holes in the bo�om of the leg at different loca�ons. Select the proper
hole that will allow access to the screwhead a�er the tub is in the desired loca�on. A�ach leveler with ¼ in. (0.63 cm.) bolt
and nut and hand �ghten it. DO NOT over-�ghten it in this step (see Fig. 4).
5. Gently turn the tub back to the correct posi�on a�er the steel legs are installed.
6. Posi�on the laundry tub in your desired loca�on. To adjust the level of the tub, move the levelers up or down. Tighten the
nuts a�er adjus�ng the levelers to the desired level. Holes on the bo�om of levelers are included for moun�ng the tub to
the floor if desired (anchors not furnished).
Coil Pull-Down Faucet
Rubber
Drain Plug





Hammer
Block of
Wood
Leveler
Steel
Legs
Fig. 3 Fig. 4
ID: 11740
Rev. 06/14/2021
1. Assembled Spout &
Spray

2. Deck Plate
3. Rubber Washer
4. Metal Washer
5. C-shaped Clip with
Screws
6. Weight
To adjust
the level of
tub, move
the levelers
up or down
PG. 1