Caloritech OKB Serie Instructions D'installation, D'entretien Et D'utilisation

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
SERIES OKB, OKD & OKH – INFRARED RADIANT HEATERS
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR
SERIES OKB, OKD & OKH – INFRARED RADIANT HEATERS
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that combustible materials
combustible materials are always kept at a safe distance from the radiant energy. This heater is
are always kept at a safe distance from the radiant energy. This heater is not intended for use in hazardous areas
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that
not intended for use in hazardous areas where flammable vapours, gases or liquids or other
where flammable vapours, gases or liquids or other combustibles are present. Remember that objects placed under
combustible materials are always kept at a safe distance from the radiant energy. This heater is
combustibles are present. Remember that objects placed under an infrared heater can take a while
FIRE/EXPLOSION HAZARD WARNING - During operation, take precautions to ensure that
an infrared heater can take a while to reach stabilized temperatures. If you are unsure of the suitability of the heater for not intended for use in hazardous areas where flammable vapours, gases or liquids or other
to reach stabilized temperatures. If you are unsure of the suitability of the heater for the intended
combustible materials are always kept at a safe distance from the radiant energy. This heater is
the intended application, check with the factory for recommendations. Failure to comply can result in personal injury
combustibles are present. Remember that objects placed under an infrared heater can take a while
application, check with the factory for recommendations. Failure to comply can result in personal
not intended for use in hazardous areas where flammable vapours, gases or liquids or other
and/or property damage. to reach stabilized temperatures. If you are unsure of the suitability of the heater for the intended
injury and/or property damage.
combustibles are present. Remember that objects placed under an infrared heater can take a while
application, check with the factory for recommendations. Failure to comply can result in personal
to reach stabilized temperatures. If you are unsure of the suitability of the heater for the intended
DESCRIPTION
injury and/or property damage.
application, check with the factory for recommendations. Failure to comply can result in personal
1.0 The OKB, OKD & OKH radiant heaters are suitable for injury and/or property damage.
DESCRIPTION
1.0 The OKB, OKD & OKH radiant heaters are suitable for
comfort heating use in non-hazardous areas protected from
comfort heating use in non-hazardous areas protected from rain, DESCRIPTION
rain, snow or splashing, where heating element temperatures
in excess of 1382°F(750°C) will not present the risk of fire or snow or splashing, where heating element temperatures in excess
1.0 The OKA radiant heater is suitable for process heating in
of 1382°F(750°C) will not present the risk of fire or explosion. The
non-hazardous areas protected from rain, snow or splashing, where
1.0 The OKA radiant heater is suitable for process heating in
explosion. The heater does not present a safety hazard when
heater does not present a safety hazard when it is installed, operated
heating element temperatures in excess of 1382°F(750°C) will not
non-hazardous areas protected from rain, snow or splashing, where
it is installed, operated and maintained in accordance with
and maintained in accordance with these instructions.
present the risk of fire or explosion. This heater is not intended for
heating element temperatures in excess of 1382°F(750°C) will not
these instructions.
use in comfort heating applications.
present the risk of fire or explosion. This heater is not intended for
2.0
The heaters are available with metal sheath, quartz lamp
use in comfort heating applications.
2.0 The heaters are available with metal sheath, quartz
or quartz tube heating elements. Use heaters with metal sheathed
2.0 The OKA heater is available with metal sheathed, quartz
lamp or quartz tube heating elements. Use heaters with
elements where there is heavy vibration or mechanical shock.
lamp or quartz tube heating elements. Use heaters with metal
2.0 The OKA heater is available with metal sheathed, quartz
metal sheathed elements where there is heavy vibration or
Quartz tube or quartz lamp elements are very fragile and require
sheathed elements where there is heavy vibration or mechanical
lamp or quartz tube heating elements. Use heaters with metal
mechanical shock. Quartz tube or quartz lamp elements are
extreme care in handling. Heaters utilizing quartz tubes or quartz
shock. Quartz tube or quartz lamp elements are very fragile and
sheathed elements where there is heavy vibration or mechanical
very fragile and require extreme care in handling. Heaters
lamps are unsuitable for applications in locations where the risk of
require extreme care in handling. Heaters utilizing quartz tubes or
shock. Quartz tube or quartz lamp elements are very fragile and
heavy vibration or mechanical shock exists.
utilizing quartz tubes or quartz lamps are unsuitable for
quartz lamps are unsuitable for applications in locations where the
require extreme care in handling. Heaters utilizing quartz tubes or
applications in locations where the risk of heavy vibration or
risk of heavy vibration or mechanical shock exists.
quartz lamps are unsuitable for applications in locations where the
3.0 To avoid damage in transit, heaters with quartz lamp or
mechanical shock exists.
risk of heavy vibration or mechanical shock exists.
quartz tube elements are shipped with the elements not installed in
3.0 To avoid damage in transit, heaters with quartz lamp or
the fixture.
quartz tube elements are shipped with the elements not installed in
3.0 To avoid damage in transit, heaters with quartz lamp
3.0
To avoid damage in transit, heaters with quartz lamp or
the fixture.
or quartz tube elements are shipped with the elements not
quartz tube elements are shipped with the elements not installed in
4.0 A minimum of handling of the quartz sheath is
installed in the fixture.
the fixture.
recommended since any type of contamination on the sheath may
4.0 A minimum of handling of the quartz sheath is
reduce service life.
recommended since any type of contamination on the sheath may
4.0 A minimum of handling of the quartz sheath is
4.0 A minimum of handling of the quartz sheath is
reduce service life.
recommended since any type of contamination on the sheath may
recommended since any type of contamination on the sheath
reduce service life.
may reduce service life.
INSTALLATION
The system designer is responsible for the
INSTALLATION
DESCRIPTION
safety of this equipment and adequate back-
The system designer is responsible for
up controls and safety devices must be
the safety of this equipment and
The system designer is responsible for The system designer is responsible for
installed. Failure to comply could result in
adequate back-up controls and safety
the safety of this equipment and adequate
the safety of this equipment and
personal injury and/or property damage.
devices must be installed. Failure to
backup controls and safety devices must be adequate back-up controls and safety
comply could result in personal injury
installed. Failure to comply could result in
devices must be installed. Failure to
Heaters must be wired by qualified personnel
and/or property damage.
personal injury and/or property damage. comply could result in personal injury
in compliance with local codes.
and/or property damage.
Heaters must be wired by qualified
Heaters must be wired by qualified personnel
personnel in compliance with local
in compliance with local codes.
Heaters must be wired by qualified
codes.
5.0 Verify that the nameplate voltage and wattage are suitable
personnel in compliance with local
for use on the available electrical power supply. Do not connect
codes.
the heater to an electrical supply voltage other than shown on the
product label.
5.0 Verify that the nameplate voltage and wattage are suitable
5.0 Verify that the nameplate voltage and wattage are suitable
for use on the available electrical power supply. Do not connect
for use on the available electrical power supply. Do not connect
6.0 Minimum space clearances from combustibles, when
5.0
Verify that the nameplate voltage and wattage are suitable
the heater to an electrical supply voltage other than shown on
the heater to an electrical supply voltage other than shown on the
heaters are horizontally mounted and installed, as listed in Table 1
for use on the available electrical power supply. Do not connect
the product label.
product label.
following.
the heater to an electrical supply voltage other than shown on the
product label.
6.0 Minimum space clearances from combustibles, when
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
heaters are horizontally mounted and installed, as listed in
Table 1 following.
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
CCI Thermal Technologies Inc. 2721 Plymouth Drive, Oakville, ON L6H 5R5 Tel. (905) 829-4422 Fax (905) 829-4430
All manuals and user guides at all-guides.com
SERIES OKA – INFRARED RADIANT HEATERS
SERIES OKA – INFRARED RADIANT HEATERS
DESCRIPTION
INSTALLATION
www.ccithermal.com
www.ccithermal.com
7.0 For chain mounting, install eye bolts supplied in the
7.0 For chain mounting, install eye bolts supplied in the ¼-20
¼-20 drilled and tapped holes located at the top of the cast
drilled and tapped holes located at the top of the cast aluminum
aluminumend plates. Use the locking nut to secure the eye bolt
For metal sheathed heaters, insulation
end plates. Use the locking nut to secure the eye bolt in the casting
in the casting at the preferred location. Fasten the chains to the
contamination
at the preferred location. Fasten the chains to the eye bolts and
eye bolts and suspend the fixture from the ceiling ensuring that
For metal sheathed heaters, insulation
suspend the fixture from the ceiling ensuring that the minimum accumulation can cause fault to the
contamination
the minimum clearances shown in Table 1 are maintained.
clearances shown in Table 1 are maintained.
element sheath generating arcing and
accumulation can cause fault to the
releasing molten metal. Install proper
element sheath generating arcing and
ground fault protection to prevent
Table 1
releasing molten metal. Install proper
personal injury and/or property
ground fault protection to prevent
A. From the nearest w all
damage.
B. From end of heater to w all
personal injury and/or property
C. From the ceiling
damage.
D. From the Floor
6.0 When mounting, maintain a minimum clearance to
E. Betw een heaters
combustibles of 15"(381 mm) at sides, 10"(254 mm) at top and
6.0
When mounting, maintain a minimum clearance to
12"(305 mm) at ends.
combustibles of 15"(381 mm) at sides, 10"(254 mm) at top and
12"(305 mm) at ends.
A
E
380 mm
[15"]
380 mm
[15"]
FIG. 1 – MOUNTING CLEARANCES
FIG. 1 – MOUNTING CLEARANCES
8.0 For rod mounting ¼"-20 threaded rods of suitable length
8.0 For rod mounting ¼"-20 threaded rods of suitable length
FIG. 1 – MOUNTING CLEARANCES
are to be installed in place of the eye bolts as in paragraph 7.0
are to be installed in place of the eye bolts as in paragraph 7.0
above.
above.
9.0 If flush mounting on a non-combustible surface, be sure to
9.0 If flush mounting on a non-combustible surface, be sure
Heaters with quartz tube or quartz lamp
slot the mounting holes (5/16" x ½" hole) to allow for heater
type heating elements are suitable for
to slot the mounting holes (5/16" x ½" hole) to allow for heater
Heaters with quartz tube or quartz lamp
expansion.
horizontal mounting only. Heaters with
expansion.
type heating elements are suitable for
metal sheathed heating elements can
10.0
These heaters are intended to be installed in a maximum
horizontal mounting only. Heaters with
be mounted in any desired position.
10.0 These heaters are intended to be installed in a maximum
40°C ambient temperature.
metal sheathed heating elements can
40°C ambient temperature.
be mounted in any desired position.
For metal sheathed heaters, insulation
7.0 For short circuit protection, heaters must be installed with
contamination or moisture accumulation can
proper fast acting fuses or breakers as close as possible to the
For metal sheathed heaters, insulation
7.0 For short circuit protection, heaters must be installed with
amperage draw of the unit(s), in compliance with the local electrical cause fault to the element sheath generating
contamination or moisture accumulation
proper fast acting fuses or breakers as close as possible to the
arcing and releasing molten metal. Install
codes.
cancause fault to the element sheath
amperage draw of the unit(s), in compliance with the local electrical
proper ground fault protection to prevent
generating arcing and releasing molten
codes.
personal injury and/or property damage.
metal. Install proper ground fault protection
to prevent personal injury and/or property
damage.
www.ccithermal.com
MI148 REV.11 Page 1 of 3
MI148 REV.11.01
MI146 REV.10 Page 1 of 3
MI146 REV.10 Page 1 of 3
ISO 9001:2000
ISO 9001:2000
or moisture
or moisture
UL
OKB, OKD & OKH OKB
U S L C N L
24"(610 mm) 15"(380mm) 10"(254mm)
24"(610 mm) 12"(305mm) 39"(1000mm)
24"(610 mm) 15"(380mm) 15"(380mm)
72"(1830 mm) 96"(2400 mm) –
36"(915 mm) –
D
300 mm
[12"]
300 mm
[12"]
ISO 9001:2000
ISO 9001
CSA
OKD &
O K H
–
–
C
B