Télécharger Imprimer la page

Eutech Electronics FACILE-MF Mode D'emploi page 6

Publicité

Les langues disponibles

Les langues disponibles

Step 2: keep the button of the original remote control you want to copy until the LEDs of the FACILE-MF start flashing all at the same
time. This operation may take a few second depending on the type of remote control being duplicated.
Now press the FACILE-MF button in which you want to insert the original code just learned and wait for the corresponding LED turn
off.
Step 3: copying was successful. For correct use of the FACILE-MF remote control, refer to the automation instruction manual.
NOTE: If the code has not been learned correctly, the LEDs relating to buttons 1-2-4 of the FACILE-MF light up at the same time,
repeat the operation from Step 1. The memory of the FACILE-MF is completely rewritable, therefore it is possible overwrite more
buttons.
FIXED SERIAL CODE DUPLICATION
This procedure allows you to duplicate the serial code of the original remote control and block its increase.
WARNING! With this copying procedure, the serial code is fixed to the current value of the original remote control. Use only with
compatible automations.
Step 1: press and hold button 1 of the FACILE-MF, then press button 3 four times. When the LEDs start flashing in sequence, release
both buttons and position the remote control to be duplicated in front of the FACILE-MF.
Step 2: keep the button of the original remote control you want to copy until the LEDs of the FACILE-MF start flashing all at the same
time. This operation may take a few second depending on the type of remote control being duplicated.
Now press the FACILE-MF button in which you want to insert the original code just learned and wait for the corresponding LED turn
off.
Step 3: copying was successful. For correct use of the FACILE-MF radio control, refer to the automation instruction manual.
NOTE: if the code has not been learned correctly, the LEDs relating to buttons 1-2-4 of the FACILE-MF light up at the same time,
repeat the operation from Step 1. The memory of the FACILE-MF is completely rewritable, therefore it is possible overwrite more
buttons.
RESTORATION
Press and hold button 1 of the FACILE-MF, then press button 2 four times. When the LEDs of the FACILE-MF start flashing in sequence
release both buttons. After waiting for about 5 seconds, press the button you want to restore to factory value, then release.
To restore further FACILE-MF buttons, repeat the operation.
BATTERY REPLACEMENT
The FACILE-MF remote control (only for V: 1.2 or later) signals the user when it is appropriate to replace the exhausted battery with a
new one. This signal is given by the LEDs relating to keys 4-3-2-1 lighting up in sequence following a key press.
Open the remote control by levering it with a slotted screwdriver in the slot on the back of the same. Replace the 3V lithium battery
mod. CR2032 respecting the indicated polarity. The batteries must be disposed of in the appropriate collectors.
WARRANTY
The warranty for this product is 24 months from the documented purchase date. The warranty covers the failure of this product for all
manufacturing defects. Therefore, those caused by neglect, improper use, tampering and weather events are excluded. Due to their
nature, batteries and worn out external parts are excluded from the warranty.
The company Eutech Electronics S.r.l. assumes no responsibility for damage caused to people, things and animals resulting from the
improper use or failure of the remote control.
DISPOSAL
The disposal of materials must be done in compliance with current regulations. It is appropriate to separate them by type
(plastic, electrical parts and batteries).
DECLARATION OF CONFOMITY
Hereby company Eutech Electronics S.r.l. declares that FACILE-MF complies with the requirements of directive 2014/53 /
EU. The remote control also complies with the electromagnetic compatibility standards EN 60950-1 / EN 301 489-3 / EN
301 489-1 regarding the health and safety of users.
V:2.0.1

Publicité

loading