Publicité
Liens rapides
Publicité
Manuels Connexes pour Danfoss 088L1457
Sommaire des Matières pour Danfoss 088L1457
- Page 1 Installation Instruction End-termination Heat shrink technology connection system...
- Page 2 Troubleshooting 10 Overview This manual introduces the installation and operation of Danfoss heat shrink splice technology. The end-termination connection is sealed with heat shrink tubes.
- Page 3 Installation Instruction End-termination - Heat shrink technology connection system Certifications / Approvals Heat shrink technology connection system for Danfoss PX/RX trace heaters. Technical data Ambient temperature range -40 °F to +185 °F / -40 °C to +85 °C Max. operating temperature end cap 185 °F / 85 °C...
- Page 4 The following instructions are provided in English only. Les instructions qui suivent sont fournies en anglais uni- Refer to www.bartec.us for the French version. quement. Veuillez vous référer au site www.bartec.us pour la version française. 088L1457 & AN296061216351en-US0102 © Danfoss | 2021.11 | 4...
- Page 5 Installation Instruction End-termination - Heat shrink technology connection system Kit contents The following table lists the kit contents for the Danfoss heat shrink technology connection system: Component Qty. Designation Dimensions Length: ¾" (20 mm) Heat shrink tube for end-termination Diameter: ½"...
- Page 6 • Veillez à ne pas dépasser la longueur de circuit de traçage maximale autorisée pour le type de câble chauffant utilisé. Consultez à ce sujet le guide de conception du systéme de traçage. 088L1457 & AN296061216351en-US0102 © Danfoss | 2021.11 | 6...
- Page 7 ½" (12 mm) over the end of the trace heater. Leave an overlap of ⅝"(15 mm). Beginning at the end of the cable, shrink the tube at a temperature of 275 °F / 135 °C. 7 | © Danfoss | 2021.11 088L1457 & AN296061216351en-US0102...
- Page 8 Make sure that it overlaps the bared part of the trace heater for ¾" (20 mm). Beginning at the end of the cable, shrink the tube at a temperature of 275 °F / 135 °C. 088L1457 & AN296061216351en-US0102 © Danfoss | 2021.11 | 8...
- Page 9 Leave a gap to the very first heat shrink tube of ⅜" (10 mm). Beginning at the end of the trace heater, shrink the tube at a temperature of 275 °F / 135 °C. 9 | © Danfoss | 2021.11 088L1457 & AN296061216351en-US0102...
- Page 10 Maximum monitoring length of Install additional ground fault the ground fault protection has protection devices been exceeded Ground fault protection defective Replace the ground fault protection device(s) 088L1457 & AN296061216351en-US0102 © Danfoss | 2021.11 | 10...
- Page 11 Risk of fire or electrical shock.Follow these guidelines to avoid personal injury or material damage. • All electrical systems and installations must comply with Danfoss requirements and be installed in accordance with the relevant electrical codes and any other applicable national and local codes.
- Page 12 Risque d’incendie ou d’électrocution. Suivez ces consignes pour éviter toute blessure ou dommage matériel. • Tous les systèmes et installations électriques doivent satisfaire aux exigences imposées par la socié té Danfoss et doivent être installés conformément aux normes électriques en vigueur ainsi qu’aux autres prescriptions nationales et locales applicables.
- Page 13 Installation Instruction End-termination - Heat shrink technology connection system 088L1457 & AN296061216351en-US0102 © Danfoss | 2021.11 | 13...
- Page 14 Installation Instruction End-termination - Heat shrink technology connection system 14 | © Danfoss | 2021.11 088L1457 & AN296061216351en-US0102...
- Page 15 Installation Instruction End-termination - Heat shrink technology connection system 088L1457 & AN296061216351en-US0102 © Danfoss | 2021.11 | 15...
- Page 16 Danfoss 11655 Crossroads Circle Baltimore, MD 21220 USA Phone: 1-888-DANFOSS (326-3677) Fax: 416-352-5981 lx.danfoss.com 16 | © Danfoss | 2021.11 088L1457 & AN296061216351en-US0102...