Virutex LR284R Mode D'emploi page 5

Conforme a la Directiva Europea 2002/96/CE los usuarios
pueden contactar con el establecimiento donde adquirie-
ron el producto, o con las autoridades locales pertinentes,
para informarse sobre cómo y dónde pueden llevarlo
para que sea sometido a un reciclaje ecológico y seguro.
VIRUTEX se reserva el derecho de modificar sus productos
sin previo aviso.
E N G L I S H
ORBITAL SANDER LR284R
1. TECHNICAL DATA
Universal Motor...............................................50-60 Hz
Power..................................................................180 W
No-load speed...........................................12500 min-1
Stroks.................................................................25000
Orbit diameter.......................................................2 mm
Sanding surface..........................................93x185 mm
Equivalent measured continuos
acoustic pressure level.................................81 dB(A)
Level of acoustic power..................................104 dB(A)
Usual level of vibrations (hand-arm)................<2.5 m/s2
Weight................................................................1.5 Kg
2. USES
ORBITAL SANDER: A single-handed sander for dry
surface finishing. Equipped with forced suctioning of
sanding dust.
To obtain a good quality finish, slide the machine over the
surface to be worked in repetitive elliptical movements
to avoid the formation of grooves on the sanded surface.
To achieve the desired finish, the surface should be sanded
several times using a finer grain of abrasive each time.
3. STANDARD EQUIPMENT
Inside the box you will find the following:
- LR284R orbital sander.
- Suction bag set
- Instruction manual and other documentation
- 1 abrasive sheet for mobile base
4. ACCESSORIES
Optional:
- Velcro base 8499219
- Centring device for sanding paper 8445571
- Standard dust collection attachment 6446073
5. SAFETY INSTRUCTIONS FOR
HANDLING THE MACHINE
Before using any of the sander models,
carefully read the GENERAL SAFETY INS-
TRUCTION BROCHURE which is included
with the machine documentation.
2. The voltage must correspond to the data indicated
on the feature plate.
3. Danger! Keep hands away from working area. Do not
hold the machine from underneath while it is running.
4. It is advisable to use only original VIRUTEX abrasives.
5. Inspect wood and remove any nails before sanding.
6. Never use the sanding machine in the presence of
liquids or excessive humidity.
7. Never leave an electric tool before all moving parts
have come to a complete stop.
8. The dust that accumulates during the sanding process
may prove to be toxic or harmful to the health (for
example, in the case of lead-based paints, certain woods
or metals). Use the dust collector connection at all times.
9. REPLACEMENT PARTS: Use only original replacement
parts.
6. STARTING THE MACHINE
To start the machine, move switch "B" (Fig. 1) to the right.
7. FITTING THE SANDPAPERS
The holes in the sandpaper "B" (Fig. 2) should coincide
with the holes "C" (Fig. 3) on the machine base.
Close clip "D" (Fig. 4), while placing the sheet of sandpaper
as shown (Fig. 5), so that it is held tight on the base.
To perforate or centre the sandpapers, accessory 8445571
CENTRING DEVICE FOR SANDING PAPER may be used.
8. CONNECTION TO AN
EXTERNAL SUCTION SOURCE
To connect the machine to the AS182K, AS282K aspirators
or to any other external suctioning source, install the
dust collection attachment 6446073 (optional accessory).
To do so, remove the suction bag "E" (Fig. 6) and fit
nozzle "F" of the dust collection attachment in its place.
The other end of the dust collection attachment is
connected to the external suctioning source of choice.
9. CHANGING BRUSHES
Brushes should be changed after 1000 hours of operation
5