Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
EN
4.4 - Learning a transmitter
A transmitter can be "learned" via the specific programming menu or by remote memorisation, using a previously memorised transmitter.
MEMORISING A REMOTE CONTROL
If you are in programming mode exit pressing the MENU button until -- appears. Press the DOWN
(RADIO) button for more than 2 seconds. Until the display shows the word "rad" (radio), then release
the button
1. Press and release the DOWN (RADIO) button a number of times equal to the number of the output
to be activated: once for output STEP BY STEP, twice for output PARCIAL, three times for output ONLY
OPEN, four times for output LIGHT ON/OFF, five times for output PRESET (button 1 = output 1, button
2 = output 2, button 3 = output 3, button 4 = output 4)
2. The KEY LED will flash a number of times equal to the number of the output selected, with 1 second
pauses between flashes
3. Press the button of the remote control to be memorised within 7 seconds, holding it down for at least
2 seconds
4. If the memorisation has been successful, the KEY LED will give one long flash
5. To memorise another remote control on the same output, repeat point 3
N.B If no commands are given for 7 seconds, the receiver automatically quits the programming mode
DELETING A REMOTE CONTROL
If you are in programming mode exit pressing the MENU button until -- appears. Press the DOWN
(RADIO) button for more than 2 seconds. Until the display shows the word "rad" (radio), then release
the button
1. Press the DOWN (RADIO) button until the LED lights up (about 3 seconds)
2. Press the button of the remote control to be deleted within 7 seconds, holding it down until the KEY
LED goes out. Release the remote control button
3. About 1 second after the button is released, the KEY LED starts to flash
4. Confirm the deletion by pressing the DOWN (RADIO) button
5. If the deletion has been successful, KEY LED will give one long flash
N.B If no commands are given for 7 seconds, the receiver automatically quits the programming mode
CLEARING THE ENTIRE RECEIVER MEMORY
If you are in programming mode exit pressing the MENU button until -- appears. Press the DOWN
(RADIO) button for more than 2 seconds. Until the display shows the word "rad" (radio), then release
the button
1. Press the DOWN (RADIO) button and hold it down until the LED lights up (about 3 seconds) and then
goes out (about 3 seconds). Release the button
2. About 1 second after the button is released, the KEY LED starts to flash
3. Press the button on the receiver as the LED flashes for the third time
4. If the deletion has been successful, the KEY LED will give one long flash
REMOTE MEMORISATION OF A REMOTE CONTROL WITH A REMOTE CONTROL ALREADY MEMORISED
A transmitter can be memorised without accessing the receiver. The user needs to have a transmitter
memorised previously, after which the procedure is as described below. The remote copy procedure
must be carried out in the area served by the receiver.
1. Press the button of the new remote control to be memorised, holding it down for at least 5 seconds
2. Press the button of the old remote control to be copied (if phase 1 has been successful, the
automation system will not respond)
3. Press the button of the new remote control to be memorised, holding it down for at least 3 seconds
4. Press the button of the old remote control to be copied, holding it down for at least 3 seconds, to
confirm and quit the programming mode
N.B If no commands are given for 7 seconds, the receiver automatically quits the programming mode
38
+
+
+ 1s
+ 1s
2 s
>3s
>3s ►
►
0,5s
0,5s
>3s
>3s
>3s
1s +
1s +
>3s
>5s
>3s
>3s
>3s
Publicité
Table des Matières
