Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
SPRAY GUNS MAY ONLY BE OPERATED IN LINE
WITH THE OPERATING PARAMETERS (PRESSURES
ETC.) SPECIFIED UNDER "TECHNICAL DATA"!
THE OPERATOR MUST CHECK THE COMPATIBILITY
OF THE GUN MATERIALS WITH THE COATING SUB-
STANCE TO BE USED. TO ENSURE COMPATIBILITY,
REFER TO THE SAFETY DATA SHEET SUPPLIED BY
THE MANUFACTURER OF THE COATING SUBSTAN-
CE!
ALL WORK CONNECTED WITH INSTALLATION AND
MAINTENANCE MUST BE PERFORMED ON A PRES-
SURELESS GUN BY SUITABLY QUALIFIED PERSON-
NEL. ALWAYS USE ORIGINAL PARTS WHEN REPLA-
CING WORN OR DAMAGED PARTS!
EACH TIME BEFORE YOU START WORKING, CHECK
THE MATERIAL AND COMPRESSED AIR CONNECTI-
ONS FOR FIRM SEAT AND DAMAGE! LOOSE, PRES-
SURISED HOSES MAY CAUSE ACCIDENTS DUE TO
WHIPLASH-LIKE MOVEMENT AND THE DISCHARGE
OF FLUIDS!
NEVER POINT COMPRESSED AIR AT PEOPLE OR
ANIMALS!
HIGHLY ABRASIVE, CHEMICALLY AGGRESSIVE,
EXTREMELY HOT OR EXTREMELY COLD MATERI-
ALS MAY ONLY BE USED IN CONSULTATION WITH
KRAUTZBERGER GMBH!
DEPENDING ON THE NOZZLE, WORKING WITH
SPRAY GUNS CAN CREATE NOISE LEVELS THAT
MAY DAMAGE HEARING! ALWAYS WEAR EAR
MUFFS WHEN WORKING!
DURING LONG-TERM USE, THE RECOIL FORCES
CREATED WHEN THE SPRAYING PROCESS IS ACTI-
VATED CAN DAMAGE THE CENTRAL NERVOUS
SYSTEM!
VIBRATIONS CAUSED BY PULSATION-TYPE PRES-
SURE GENERATING UNITS (PUMPS, COMPRES-
SORS) CAN BE TRANSMITTED TO THE SPRAY GUN
VIA HOSE LINES. DURING LONG-TERM USE, VIBRA-
TIONS CAN CAUSE DAMAGE TO THE NERVOUS
SYSTEM AND VASCULAR DISORDERS. VIBRATION
LEVELS CAN BE REDUCED BY USING PULSATION-
CUSHIONING DEVICES (PRESSURE EQUALISATION
TANK ETC.)
SAFETY NOTES WHEN USING
HAZARDOUS SUBSTANCES
ALWAYS COMPLY WITH THE STIPULATIONS IN THE
SAFETY DATA SHEET OF THE MANUFACTURER OF
10
OPERATING INSTRUCTIONS
THE COATING SUBSTANCE. IN PARTICULAR, ADHE-
RE TO INSTRUCTIONS RELATING TO: - THE
WEARING OF PERSONAL PROTECTIVE EQUIP-
MENT.- THE AVOIDANCE OF EXPLOSIVE OR HARM-
FUL ENVIRONMENTS.
ROOMS IN WHICH HAZARDOUS SUBSTANCES ARE
STORED OR PROCESSED MUST HAVE ADEQUATE
VENTILATION. IT MAY BE NECESSARY TO INSTALL A
TECHNICAL VENTILATION SYSTEM. IF THE VENTI-
LATION SYSTEM FAILS, WORK MUST BE STOPPED
IMMEDIATELY!
DO NOT STORE ANY FLAMMABLE SUBSTANCES,
EMPTY COATING SUBSTANCE CONTAINERS OR
OTHER MATERIALS THAT HAVE BEEN IN CONTACT
WITH THE COATING SUBSTANCE (PAPER, CLOTHS
ETC.) WITHIN OR IN THE WORKING ZONE.
IN THE WORKING ZONE, AVOID OPEN FLAMES AND
RED-HOT COMPONENTS AS WELL AS EQUIPMENT,
TOOLS AND PARTS THAT CAN CREATE IGNITABLE
SPARKS.
HANG UP "NO SMOKING" SIGNS IN A 5 METRE RADI-
US OF THE WORKING ZONE. MAKE FIRE EXTIN-
GUISHERS AVAILABLE IF THESE ARE NOT ALREADY
IN PLACE!
MIXING OF DIFFERENT COATING SUBSTANCES CAN
CREATE SUBSTANCES WITH INCREASED HAZARD
POTENTIAL. ADHERE TO THE INSTRUCTIONS OF
THE MANUFACTURER!
COMPLY WITH ALL NATIONAL AND REGIONAL
WATER PROTECTION REGULATIONS.COMPLY WITH
ALL NATIONAL AND REGIONAL WASTE DISPOSAL
REGULATIONS.
FRICTION CHARGING DUE TO FLOWING COATING
SUBSTANCES AND/OR COMPRESSED AIR CAN
LEAD TO ELECTRIC SHOCKS DUE TO ELECTROSTA-
TIC DISCHARGE!THE SPRAY GUN MUST THEREFO-
RE BE EARTHED!WHEN THE GUN IS USED IN
POTENTIALLY EXPLOSIVE AREAS, THE AIR AND
COATING MATERIAL LINES MUST –BE ELECTRICAL-
LY CONDUCTIVE (<1 MEGAOHM) AND MUST BE
EARTHED.
STARTUP, CONNECTIONS
Connect the compressed air supply at the
connection point (item A)
Make the necessary material feed connec-
tions. Via feed cup (M), suction cup (M') or
hose (M')
Document: DOK-009
mail@krautzberger.com
Publicité
Table des Matières
